Відео

Cheile astea chinezesti,niste rahaturi.Nu se potriveste cablaju,bateria ,butoanele,etc.Sint f diverse.

That knife was scaring me!

Not copper grease!

Brilliant, thank you. Your video gives me enough information to have a go at this myself. Fingers crossed!

Improper and illegal your can't double land wires into a terminal made specifically for 1 conductor

Where did you get the boots for those connectors? Did you get them sperately?

Those twist on connectors should be outlawed. I replaced so many of those when I worked for Brighthouse Networks for being the colprit of all kinds of problems.

I would like to try this someday to replace the under hood light bulb switch in my dad's truck. I will use a test light probe to make sure electricity is getting to the switch. If there is electricity then the switch itself is bad. The switch is Mercury controlled to turn on at an angle, But I like to replace it with a on off switch. I'll have to figure out how to properly dispose of the mercury switch

Fun project idea! A soldering tutorial i watched says to heat one side of the solder joint and touch solder wire other side to melt the solder onto the solder joint. They say mistake is to apply solder directly from the soldering iron. So i feel like this technique may help you in your soldering! ua-cam.com/video/Qps9woUGkvI/v-deo.htmlm4s

😊😊😊😊👍👍👍❤

Wrong all of them

WRONG! WAGO are not rated for aluminum and copper connections..

Falsche Länge abisoliert. Es muß immer mehr abisoliert werden als der Kabelschuh lang ist, da der Kabelschuh beim Verpressen sich verformt ubd länger wird. Falsch gepresst. Man fängt vom Loch her an. Es gibt von Klauke eine Pressanleitung.

Thanks sir ❤❤❤

This is only 'Super easy' if you have hundreds of dollars worth of equipment! Pointless video!

Could you give us a diagram of the parts?

Buna,cum ai reusit?

Unfassbar!!! Nutzloser kann eine Anleitung nicht sein . Wirklich wolltest Du nur zeigen daß Du es kannst ?

This is actually not a great connection at all your better twisting wires togwther beforehand...solid connection plus it holds wires in place so u dont do what dingus here did😂

What is the name of the second pin that you used

On 5.03min, that's not the way to go. this is potentially a fire hazard. You need to use the right plier first.

Very good💥💥💥

What is the name of the tool that is used for cable insulation cutting

👌🏼👌🏼

Wrong crimp direction. Proper crimp direction is from inside out of the terminal lug not from outside in . Proper crimp direction helps to reduce pressure of crimped material inside the terminal lug.

That first twist was incorrect.

Не работает

How long does it take you to do all that?

Always start from the hole point to the cable side. Otherwise you press the copper from the lug further from the cable itself leaving a hollow space between cable and lug when you are done.

Did the hood open button work by chance?

Check out the list of tools I use on amazon.com/shop/rorotech

Do you have a link where you buy your connectors

Now if you drill the front out with a small hole. Then With a torch and solder you can completely fill the inside with solder. That’s how we fabricate our bonding/Grouding straps. Elements be damned, nothings getting in. Then some industrial heat shrink and bam! Pro leads.

Please send buy link

What cable sizes and connectors are matched?

No tool description or info on rhe terminal used.

Is it changable of eletrical oven whre the wire has eaten by rat?

just use a pair of coaxial strippers?? this whole procedure becomes 5 seconds. i swear no electricians know this and i've come across so many terribly crimped cable ends that cause faults over the years that just havent been stripped or pushed on properly.

My cables are too thick to screw connector on. I’ve tried two different cables.

Very neat installation

Easily buy what you need here amzn.to/3EU4jH6

Where to get that connector? Can purchase it to hardware's?

very helpful

Electrical wire conectors and recommended tools just for you: www.amazon.com/shop/rorotech

Check out the tools I use for electrical wiring: www.amazon.com/shop/rorotech

watch your finger

June 24, 2021

Hey rorotech do you think a two spitter that is hooked to a coax cable enables others to wiretap and monitor my activity?

Why crimp solder

Sir ji, is machine ka price kitna hai?