Відео

Correct.

Yes all the door and boot/bonnet show. My van already had ambient temp sensor fitted.

@@tobes49 awesome work! Did you have to bring any extra wire to/from the BCM to the new dashpod to get the MPG info?

Yes, I added a siren, from memory it uses a power and earth feed and then a data wire to the CCM. The alarm fits in the bulkhead under the wipers.

But what it is the T5 didn't come with an alarm unless you paid for it.

Ok thanks!!

Toby Gardner hello bud, I got the exact same problem, don’t suppose you can recall what pin on the ccm the data cable has to be sent to? Had an attempted break in the other night, and use my van to respond to 999 calls, only knew something happened when I seen the indicators flashing and disturbed the scrote.

pro tip : you can watch movies on Flixzone. Me and my gf have been using it for watching lots of of movies lately.

@Elisha Deshawn Definitely, have been using flixzone for since november myself :)

You can try but it not guaranteed to be correct. I would also try an autotune as this seems to work very well now.

It a CNC3020. If you look on eBay there loads for sale. They also do 3040 and 6040 versions

Toby Gardner so only 300w? Seems to still do the he job but I guess just takes a few more passes. Is the repeatability good enough to leave a nice finish on the edge? And is there much movement in the rails, does sharper type turns leave a nice consistent radius? Hope so, think I saw these for <$500, the 6090 I been eying off is $1800-2000. Plus god knows what other costs are to be discovered along the way

Toby Gardner cheers

@@muntee33 it a little under powered but have cut aluminium with it no problem just take a lot off small passes.

sabbir rahaman ask away. Better everyone see might help people I the future.

Mine went strange once and I had to reload the firmware to get them working again

same here - this is the hell - my props stuckin so hard that i kill thm if i try to remove them again - and this is this is necessary after firmware reload ^^

Camilo Jaramillo when I did the video the microphone wouldn't work. must do another one with the audio.

Not sure? Save all the parameters and reflash the board with new firmware if all else fails.

You could try changing - AUTOTUNE_AGGR to 0.075 a re-run the autotune, Or lower the P gain as a start.

Toby Gardner many thanks for your reply. After many hours of tuning I found that the 'd' gain needed to be increased, now there are no oscillations at all.

Samuel Klassen We don't have any plans, we just guessed it and made quite a few changes. we're still makes changes for this year.

Toby Gardner can you maybe send me pictures where i can see how you built it???

Samuel Klassen check t49.net website you will find pictures off both ones we have built

Try an autotune first providing you dont have "sync problems" If your flight time is under 15min please change "AUTOTUNE_AXIS" to 3 (this will only do roll and pitch) Once happy with roll and pitch change "AUTOTUNE_AXIS" to 4 to finnish the yaw

I kind of scared for doing autotune cause, I mounted a gimbal and camera on the top of the drone which might cause the quad to crash in autotune. so whenever I pitch the quad tilts about 30 to 20 degrees due to the cg offset to the top and it wobbles and it comes to stable position. even in poshold it wobbles at a stationary position. Is it advisable to reduce the Stabilize_pitch and Stabilize_roll from 4.5 to 3.5 or 3? thank you....

Check the basics first TX Calibration ESC Calibration Also are you trying to take off in stabilize?

Yeah I check TX and ESC so the Cheerson TX is Very odd, This calibration is particular. Im Trying to take off GPS no assistance. stabilize mode. so when I chance to loiter mode I dont feel any difference.

If the tx and ESC Cailbration are good then you try downloading the logs and check throttle in and throttle out. how heavy is the quad? also might be better to post on the APM 2.x and pixhawk group on Facebook as there me and lot off other helpful people on this group.

either post the question here or on the APM 2.x and pixhawk group on Facebook is the best option.

I've never needed to set any settings that low? is it on a 250 size quad?

Yes, i am using on very large size quad. But i have already settled it. Thank you.

I have cut A4 carbon fiber sheet before clamping on the long ends the sheet fits on the bed but you can cut that wide (bed is wider than A4 but the spindle doesn't go to the edge. - ua-cam.com/video/Po-5j8X6ND8/v-deo.html Yes you should be able to cut 297x197 but I would say 295x195 is more like it.

You can't do it with VCDS. See the link for how to do it.

Thank you It a RC Devices brushless gimbal, with 3d printed rubber front mount conversion SJ4000 camera the gimbal is made for a gopro and the sj camera has to be mounted across to get the balance correct.

+Toby Gardner Is that really the SJ4000? I would've probably guessed it was a GoPro because of the way it handled that low light situation. The gimbal seemed to work good as well.

+Joe Quadcopter Ive been impressed with the SJ400 camera. I have gopro's version 2 and 3 and the picture seems to be better from the SJ cam.

We made this one with some old tubing and wake/surf board. You can buy them from here - www.zapata-racing.com/en/hoverboard/

It's acrylic but be careful there are 2 types - I brought some 3mm and 5 mm sheet from the same company. The 3mm cuts lovely, the 5mm cuts but clogs the cutter up! I've been told there cast and extruded - Sounds like the 3mm is cast and 5mm is extruded The tool is engraving tool -

Thanks, im about to get my CNC router delivered and doing a lot of research and videos. great info :)