- 8
- 40 024
Dani d Passport Integra
Приєднався 16 лис 2013
My 98 teg coupe 5spd swap,
Digi Dizzy and Burton racing coil and plug plate install
Digidizzy with Burtonracing coil plate and k20coil pack installed in non vetch b series
Переглядів: 1 233
Відео
Acura integra window regulator replacement
Переглядів 2,1 тис.Рік тому
Acura integra window regulator replacement
SKUNK2 pro s2 coil over top hat bushings replacement
Переглядів 2,3 тис.2 роки тому
Tools used: impact gun, PB BLASTER, 12mm, 14mm, 17mm, 19mm I used 3m silicone paste but you can use white lithium grease this is a good opportunity to inspect your coil overs pre load and heights , these were in my car for 3 years
Integra oil leak solved
Переглядів 3 тис.2 роки тому
1998 Acura integra Ls , had this oil leak for the past 6 months or so , I would add about a half quart of oil every 2 weeks and I taught it was my rear main seal that was leaking. Thankfully after cleaning the engine bay I noticed oil drips coming from the oil pressure sensor wire. I had to use a pick tool to remove the rubber boot that was hardened over the sensor and as soon as I pulled the c...
Integra P0171 P0170 Running Lean So Did Some Work
Переглядів 3,9 тис.4 роки тому
So after doing this my car idle was fixed, 600 rpm after 5 min warm up in about 70 degrees F out side temp, the check engine light came on for p0171 and p0170 ,later that day I found an exhaust leak by the v band connecting the down pipe to manifold, i got it welded and now no more check engine light ,Also I found my rotor screw from inside my distributor cap off and chewed up the rotor and con...
Yaheetech squat rack lock nut installation
Переглядів 3,9 тис.8 років тому
Having trouble with these nuts ? Lol try a ratchet and pliers
You don’t need to compress the spring?
Great video! But I really hated how you were whispering to me like we were cuddling in bed
How is it going so far?
🔥🔥🔥
Good work Dani, super clean looking now, and it sounds beautiful. 🎉
Thanks man
just used this video to swap my regulator out, had the exact same issue. Thanks for posting!
Is this a 4 door or 2 door
2 door , the 4 door is completely different
This is exactly what I needed to see! Thanks man
Me too thanks man! Welp I guess I’m ordering bushing again…lol
Great another thing to check :p
What’s your wheel and tire set up size wise
Did it fixed the oil leak?
Yes
B18b1?
Yes
Clean car bro thanks for the vid
Thank you,
I have my nylon nuts facing up (opposite direction) like in the Amazon video Yaheetch. I was thinking the bolt would make contact with the floor when upright pos, and scratch my hardwood floors thus making it make uneven, but it doesn't either way. Don't use the pliers he's using It'll strip your bolts.
Bless
Saludos
Desde panamÁ.
Saludos
Bueno
Saludos
Desde panama
Saludos
2020 u solved my problem! Thanks 😊
Good looking out, saved me from having to bother my pops...
thank you bro, saving me 4 years half a month latter
Was just about to go to the hardware store for some new bolts 😄. Thank you 👍
So wat did u think was the issue for the code?
It end up being an exhaust leak by my vband clamp , i have a 1320 uel header , i end up getting it welded
I just got those codes today, I have tried looking it since it’s night time, it’s not a serious issue is it ?
@@Alexis-jw7ov sorry for the late response, it can lead up to a serious issue meaning your catalytic converter will be damaged, your o2 sensors might need to be replaced, your fuel economy will be horrible , as well as sprak plugs will get fouled out,, did you check if you have a exhaust leak ? Also a bad pcv valve as well as vacuum leak can cause these codes
Clutch
Life saver
thanks man
Locking nuts... I didn't know they can trick so many humans.
Get that NUT off lol
Wow, I learned I'm retarded in 2 minutes.
Good explanation. Thanks!
Lol ,thank you so much for this. I'm retarded when assembling things and was about to give up and return it.
same here lol
Thank you for confirming that it was not my power cage that was defective when really the only thing that was defective was me.
I bought this machine today and good thing I found this video. Thanks man.
Thanks for your post. And thanks mostly for no B.S. and just getting to the point. By the way, that's fucking rediculous just to change sparkplugs.
Great job! How long would you say the entire process takes to remove everything and put it back together? Also, what would you estimate as the total cost, assuming you had no tools?
Antious Maximous 30mins
Price depends on where you buy from
Thank you for your reply!
you used the old gaskets when putting everything back and had no problems?
Eduardo Macedo , the only gaskets I reused was the throttle body and the egr, but the intake manifold one I got a new one
Thanks For The Helpful Post!