Відео

Bro❤

Nice, it was very helpful.

Thanks for the video. Yesterday we came across one trouble shooting of LVM at generator. The phase voltage is available at the input side or L1,L2 &L3 side but still the LVM green light is not switching on. Can toy suggest what all to check

How i can take training from you

Good explanation

Good sir ❤

Which software used

Hello! In my configuration, several frequency converters are connected to port number 1, and a Weintek panel is connected to port number 2. Both are Modbus RTU. Please tell me why, after physically disconnecting the frequency converter from the RS485 network, the M172 controller continues to display on the Weintek panel the current and frequency that were at the time of disconnection? Thanks!

Hello! In my configuration, several frequency converters are connected to port number 1, and a Weintek panel is connected to port number 2. Both are Modbus RTU. Please tell me why, after physically disconnecting the frequency converter from the RS485 network, the M172 controller continues to display on the Weintek panel the current and frequency that were at the time of disconnection? Thanks!

Ok

Thank you👍

Hi😊

Nice video ... Could you please share your contact no ?

Please make a video.how to calculated under voltage and over voltae

Well explained.

will you please send me the contact number

Hello brother, how to change language from FBD to LD

Hii sir

Sar apna number de dijiye

Is It used to control the discharge pressure of the pump or just to show the pressure of discharge in panel? Can I run the pump safely without the transducer?

Does this pressure transducer function as an automatic pump control thanks

hiii @switch Gear & Automation, very nice video, will you please create video on Analog input controlled by digital output how can we do that?

Hello! If supplier doing FAT AHU and LCP separately not fully complete unit and shipped separately as well. Do you know is any risk - any issue construction can faced . Any experience? Thank you

Hello Dear Do you have practical connection for 3 wire 4-20mA sensor with Siemens LOGO. I think you need to add a 500 Ohm resistor. your reply /schematic will be highly appreciated.

Why did you use those parameters in the gain scale? Im trying to learn zelio but im a begginer

why supply fan is off in case of fire? plz explain

how do you calculate the resistor value or rating?

thanks

Sir, my project have temperature and pressure in plc inputs , how this inputs reading values to give BMS pls make one video clearly pls ,......

Thanks

Ji, I saw two FAHU UNIT ,one run other one stop. Some amount of air came stopped unit the motor rotate reverse side in this case we do install braking resister?

Good morning bro,I am a new learner,watching this video.I try to do this project, timer working properly but pressure not controlled properly .In this video after PI controller fixing not shown clearly.in the PI controller first point where its connected.so kindly clear my doubt,how to pressure controlled as soon as possible

Thank you sir nice explanation 👍

Perfect my friend

hai

Talk faster,and use more ok pffffff 🙄

Most ok

Hi sir now Q3 simulate pump is two times on how?

Sir how to use this relay for genset

Hindi me bol Bhai koi itna kabil hota to Teri video nhi dekhta

I like how you describe the resistor as a load on the motor taking energy from it and stopping it.

😂

Merry pas hai really idiction dey rehe hai set Nahin ho rehe

Sir over voltage problem how to solved this please reply

Thank you sir, I understand clearly

Nice bro

Good vi❤❤❤

Super

Thank you! I was stalled in my progress trying to merge timer with pressure based alternating pumps and this video helped lots! My next step along this path will be incorporating delayed “lag pump on” to assist the lead pump reach set pressure.

Thanks you for sharing this great feature!. Is there a way to add a message that indicates which pump is running in a dual pump boost pressure system? ie suction/discharge psi as well as indicate which of the 2 pumps in running and which is off? Thanks again!