Відео

Please can u tell me the maximum size of a phone that can go into this ?

Should i buy the odbeleven ?

Did you loosen counterclockwise?? Or clockwise?? Because looking at the video while you were looking i thought you were loosening the opposite way , but im asking because ill be installing them and i want to make sure i dont cross tread or anything

i finali montano su diffusore originali? non toccano?

What front lip are you running?

brought 2 different ones for 2 different shops, drive select works on both but start button both dont work! wired up exactly this video still doesnt work buyers be aware!

Im doing this myself, but im running into an issue with the start and srive select button. Ive got power but thats all, i see blue/gray/white wires. I took pins 3 and 6 then put them into the conversion harness. Ive switched wires but nothing is working. Do you know what the 3 colors are for the conversion harness?

What's your exhaust system?

What rims are these bro? Can you send through the link

how can u put the red ring on it again?

I can’t find a place To put the tubes on the doors

How did you do the doors I can’t figure out where to put the strips on the doors!!!

Where did you source the jumper cable you show at 17:20?

How fast is the charging speed?

I have an Audi a4 b9, is it also the same pin assignment there that you have to pin out?

400 euro for this kit is criminal

The power cable you connected to the usb port instead of the fuse box, does it affect anything? I'm usually skeptical doing that if the supplier supplied a fuse connector

Does the adapter come with it. Not sure if it’ll fit my CTS downpipe I have

Thank you

you need to block off your intake also do to how physics work the wind rolls back in the engine bay if you do this mod

Wouldn’t it be best to sand down the 2 screw ports so it sits flush? I wonder if you bough one that didn’t flatten them.

Thanks soo much man!!! Was seeing the same thing. Went straight to look at if the wires were broken or not, and found a snapped wire. Not sure who in Audi had the bright idea to design it this way. Fixed it. Works great now!! BIG THANKS AGAIN!!

did you miss to lock the knob after you put the new back on?

But it doesn't get rid of the seat belt light, so you get to hear the warning thing continuously while driving.

it's would fit if i just take dbv2 turbo inlet pipe in stock is38 and pipe stock?*

sooo good :)

Thanks! I’m getting oil changed today 🎉

What about the front & rear indicators ?!!!

This is NOT a mod. The strip is to prevent water from getting into the engine . It also stops any gases etc from the engine bay from entering through the intake vents for the air conditioner. I value my health more than trying to “make something from nothing “.

Hey, what are the resisters called please ? I'm getting Sparco R100 seats fitted but haven't been able to source the resisters I'll need to avoid warning lights. Also what are the jumper cables as I can't seem to find them either. Im in the UK / Scotland, Thanks

after watching this video we ordered the Airbag cover + TTRS Buttons and are hyped to install it :thumbs up:

Nice job

Just in case it was not mentioned. I struggled to get the mirror caps back on. Taking out the side assist sensor (just two clips that push in) and feeding the wire through the hole allowed me to align the peg and the slit clip of the mirror cap. Attach the wire harness then put the sensor in at an angle.

thanks for saving our life 🙏😂😂

does it work for iphone or do u know of a similar?

Great video! I got this same kit for my 2019 S5, but I cannot get the Drive Select button to work! The engine start stop button works fine, but the other button does nothing. By chance were there any extra steps you didn't show for the drive select button, or did it just work out of the box? I'm a little confused, because pin 3 and 6 shouldn't have anything to do with the Drive Select button, but you didn't do any other wiring under the center console! Any help would be greatly appreciated!

Tu n’a pas mits le lien pour le bouton bloquer

Pomoemu viglyadit kak ponos

top job, cheers

W Jahn, W Review

Wouldn’t it be even quicker and simpler to buy a wireless charger pad and just power it through the usb or the 12v slot?

Does it cause the phone to overheat? Which phone model do you have? I was going to place an order, but I am concerned that it may not be compatible with the latest phones. It appears to be designed for older phones with Qi charging capabilities.

Thank you your vids .. helped me heaps

OEM like ? errrrr AliExpress - ahhhh now its a definite hard pass rofl that looks abysmal fitting !

More

Where do the small springs attach? One of mine has completely fallen out

Woah its been a while! Good to see you back brother! 👌🏼🔥

Good explanation but not like orginal

What happened to the s3? Its dead aye no more Content?😊

Plastidip doesnt last long if its being touched and cleaned. Just paint the damn things