Відео

useless

All new water heaters are 🗑. Bring back the old mechanical valves. Planned obsolescence.

I bought Bradfordwhite water heater and after 6 months the pilot light is having trouble and not only that there are dark sooth appeared on my ceilings. My HVAC is 6 months old and I don't think that causes the issue and I think my water heater has lot of issues. I called the support but all they say is call a contractor and troubleshoot it with our technician. I've been dealing with this same pilot light issues for months and no fixed at all. They should had replaced my water heater at first having this problem.

What if my water is hot for about 5 minutes and then it suddenly turns cold?

This video is hilariously uninformative. Also: If your computer isnt working make sure it has power.

I am sorry I bought this tankless water heater. Almost every month I have no hot water

What about the wire to control board and face and ignitor

Nothing about thermostats. Oh, dear.

Y y’all need more videos on troubleshooting

Where the diagnostic light

much too complicated system. TRD and closed air supply. Federal regulations? Gas water heaters worked fine for decades.

What a terrible video

You are useless duuuuude , great job ,

NTC Thermistor 10K at 25C with a B25/85 value of 3975. Really any B value within a couple hundred of that will work fine and B25/100 or B25/50 is about the same. Instead of a 3 wire, you can get two normal ones that match and wire two legs together. You can get them on digikey or even amazon and major brands include Vishay, TDK, and MMTL, but it's hard to mess up making a thermistor, so any brand is probably fine. This part should be under $10 and available separately instead of bundled with a $200 controller.

Great video and highly informative. I reviewed my BradfordWhite service manual which says the following in regards to diagnosing the heating ellement: "Reading should be 12.8 ohms (±6%) for a 240volt, 4500 watt element. A reading outside the range using the formula above (±6%), indicates a bad element and the element must be replaced." So I checked both upper and lower elements and my multimeter shows 12-13ohms initially and as I held the multimeter on the contacts the reading dropped to 9.5ohms after 4-5secs. Im not sure whether to go by the initial 12-13ohm reading or the 9.5ohm reading 5secs later. Do you think I have a problem here? The heater is the M250S6DS-1NCZZ and id about 15 years old. Thanks in advance for any further info.

Why came to here useless?

Where is the led indicator

Useless

"if you have power, your heater should be working properly" Thank you, Mr Wizard! What a waste of time!

Don’t buy their junk, mine had issues 4 months after installation and main board blew 2years & 2months after installing

Don’t buy their junk, mine had issues 4 months after installation and main board blew 2years & 2months after installing

Don’t buy their junk, mine had issues 4 months after installation and main board blew 2years & 2months after installing. Customer service is a joke.

useless

Wow this video was completely useless.

Help my water heater turn off and shows 981 on the screen.. what is that mean?

Thank you very little.............

Hi. Thanks for video. Quick question. My Bradford White water heater's pilot stays on on but the burners do not go on to heat the tank (even when I turn the knob to highest heat). Any idea what could be the problem?

I got the 5 flash’s am I done for? Or can I fix this?

why does this unit along w/ its plumbing look like a small nuclear reactor or something?!? got to be a more attractive way to run your input/output lines.

Agree, what a waste of video space!

I had one of these water heaters installed in my basement. A 50 gallon, I have ran out of hot water multiple times after having it installed a few days ago. I have it set to Hybrid mode. Is there something that can be done to rectify this problem?

Great Video. Did you see this one? Bradford White Water Heater Error Codes ua-cam.com/video/wMgxzxsrzr8/v-deo.html

I have a 5 flash error code. The water is always lukewarm. Your thermistor readings were almost exact. I have one thermistor reading 5.33K and another reading 5.70K. Both indicate a water temp of near 100 degrees, and the actual water temp is 98-100 degrees. What is the max allowable difference for these readings? And why are the thermistors not replaceable?

??? 😲

Thanks. This was an excellent internal look at the temperature sensor (thermistor) providing dual resistances to the circuit board. I can generally see why it may be difficult to replace known sensor in that it appears to be permanently mounted thru the gas controller hardware. I assume then, that a new thermistor is part of a new controller assembly. Thanks for the clear technical details. I currently have a code five flashing, as I had noticed our water temperature had been fluctuating, which caused me to look at the controller. (As a side note, I keep my water heater temp. set very high, to maximize availability of hot water for baths and showers. I wonder if this practice contributed to a sensor failure). Anyway, after confirming with this video, that I may NOT be able to simply replace the sensor, I'll try the circuit board reset first, to determine if the error code magically goes away. If the code returns, I'll then remove the cover and read the resistances to test the sensor. This will confirm that is the cause of my problem. Thanks Again.

Total waste of time, tells you nothing

Excellent breakdown so I can understand better. So code 4 is a complete shutdown and now on UA-cam homeowners have finally found out how to do the reset. As I plumber I replaced two valves under warranty instead of telling me this reset measure. There may be a problem with overheating due to physical situations with heater air flow that are not getting remedied by me replacing the valve each time. So it's important that the heater is properly vented to code, has enough intake air, and the filter is not clogged on the bottom.

Thanks for helping to keep Michigan's economy and families going!

Yeap, that’s worked for me 🙌…Thanks!!!

Hirsch Pipe & Supply here.

Helpful.... Thank you.

What does 3 flashes and 3sencod pause mean?