Відео

How to calibrate Dodge Magnum 2005 3.56 cylinder Rear Wheel drive SXT

What aftermarket fuel gauge do you recommend to use with the Crown sending unit? I want to use it on my 1980 CJ5. Want to keep the speedo cluster in the dash. Thanks.

What ohms setting on your multimeter do you use? I want to calibrate my Crown sending unit for my 80 CJ5. Tank is a 15 gallon poly tank from MTS. Thanks.

Wish there was a video for the majority of other fuel sender units

thanks>Not sure what is MD but good info

What about the abs scanner/auto bleed?????

LMAO.... I wish i knew about this 6 years ago. I have slipped out of the jeeping community over the years, but front caliper seizure got me on the hunt again. I have this kit on order now. Reading the comments let me to search for the rear kit. I'll have to order that later... but it's gonna happen. The gutless wonder is getting a brake upgrade. FINALLY.

Where do I go to get an OEM sending unit spec for a 1986 Toyota with a 22R engine?

The upsized master cylinder fits the ‘15 and up booster correct ?

great help as i'm about to do my 1970 ford zodiac thanks

Thank for the video. Helped me fix my motorbike fuel sender 🙌🏼

Thank you

HI IS THIS FOR ANY TANKS ? I HAVE A RV AND NEED TO DO THIS.

What’s the part number on that oversized master cylinder?

great sir. thanks!

I rebuild senders professionally and this is not how you calibrate a sender. The two stops are intended to keep the float arm from hitting and drumming on the top of bottom of the tank. The actual calibration is done inside the resistor housing by adjusting the location of the sweep arm. As Ellesmere Wildwood pointed out the resistance at full should be no higher than 10 ohms. Setting it a little lower compensates for the series resistance in the rest of the circuit. As a percentage being 1 ohm off at 10 ohms is meaningful. At 73 ohms empty one ohm makes exactly no meaning full difference. Because of the design these senders are only calibrated at the full position. If the empty reading is too high it means that you are compensating for series in the connections in the sender by having to really drop the full setting to get total resistance in the sender down to 10 ohms.

So since there’s to bolt lights, do you join them together then wire them to your tail lights? Thanks

I just installed this on my jk. Great kit and significant difference in stopping.

Very helpful new sub here

My car uses a different style unit that won’t allow me to bend tabs to adjust the reading my manual calls for 3ohms full/80ohms empty the replacement unit I received reads 6.5omhs full/82.5 empty will that cause an issue ?

Interesting, but the "fix" by setting stops on the float motion effectively makes it non-responsive around the F and E limits. At least keeps the customer happy since they see exactly full on the dash gage. More critical is how accurate it reads near empty. Perhaps the stop is why most people figure they can keep driving a bit more when it shows "E" on the gage and the needle stops moving.

Great Vid.

Sorry mechanics, due to the pandemic I can no longer support your businesses 🚫😂😂😂

I bet it still shall not stop as quick as my Dodge Ram 4X4 4 door. Breaks on that are a beast, about 7000 pounds..Jeep 4 door about 4200. Jeep let us down on the breaks, for what a Wrangler Cost they can do better. Sun visors are too short, sun Blinds me ran out of the road. Hard Top rain gutter, open door water runs into floor. No power seats for the price and NO Dual Exhaust like most other SUV's...

Back in the day, working at Flexdrive Instruments, the Aussie arm of Stewart Warner, the tank senders were always set slightly low at full. For instance the 73-10 ohm tank the 10 ohms would be set at 9 ohms so the gauge pointer would read slightly above full. Apparently, back in the day, people liked their fuel gauge to read slightly above full. Gauges were always calibrated exactly on the mark. Low on the sender would be set at correct ohms or a little higher like 75 ohms would be acceptable. These days, when ever I repair a tank sender I always set them the same way as it was done at the factory, always a little higher at the full mark (9 ohms) but never higher than the 10 ohms. Anyway, just 2 cents worth from the old school instrument guy. 🙂

I wouldn't put the filter on at all. Because you have a filter after the tank anyway and it's a pain to get to.

nice tutorial 👍 please visit channel - THE EXPLORER FOR ALL 1 . paano mag repair ng fuel gauge floater napupundi sa gas 2. paano mag repair ng starter relay bubuksan natin 3. paano gumawa ng tester light for continuity 4. paano mag tune up valve clearance

You can get those digital gauges that can be calibrated at the back with a simple screwdriver

Why no rear kit? Guess I'll have to use the Powerstop Z36 pads in the meantime

I bought this kit and they sent me the wrong banjo bolts. I eneded up using my oem ones. They worked just fine and jeep stops betterafter install. I don't know how you package the wrong parts in the kit. Still a great kit for the price.

Are there to different topper versions, soft top and hard top?

This is an amazingly clear installation video. Very cool that they thought to use everyday tools that their customers will be using. Great job to the designers and editors.

Good video any plans on making a rear kit thanks.

Dope trick thanks

Trying to buy this product its showing it's no longer available

I've heard that Crown is working on a JK Wrangler Big Brake Kit for the rear as well. Any timing for the rear kit availability?

What is the replacement brake pad part number? I hear that it's the same as a Ram 1500.

Thanks for posting this video Crown Automotive, thank you for also sponsoring the Obstacle Course! This LJ was really cool, Bruce did a great job with this build.

See these tough HD RT-Offroad ball joints at Russells Automotive Depot

Neat trick helps protect the wheel bearing from damage as well.