Відео

Yes but my first one was 40 years ago.

TY no it does not. The magnets are to align and hold the canopy in place while I use 3 mm screws to secure it. I don't trust magnets for flight as others do. If during flight there is an unbalance the canopy will fly off no matter how strong the magnets are. It happened to me...😀

On the Fun-key which is on the small size, I use 640 blades and I flew it also with 680mm. Yes I think 700 is a bit of overkill.

@@romeooscar8495 im building a new trex 700 with funkey fuselage.. but i think using 5x 700mm will overrotate the heli out of control. At least what happened when i testet my 800size with 4x 790 blades.. even had huge 3blade tail rotor but had no tail authority at all

I agree and like the 640 on mine. Of all the models I built, it's the one I prefer to fly. ua-cam.com/video/ZSrWtnAuUh4/v-deo.htmlsi=0O_bPkGp0AYECJpW @@robertlunatic

@@romeooscar8495 Don`t mind. I fly 6-blades 600mm on an 600size MD500.

@@robertlunatic You need to set up the Flight Controller according to the rotor. I am with 6 blades 600mm on an 600size model. Don`t try to use a typical 2blade 3D setup.

I always used the TD hooked up via the s.port connector configured as FBUS with MSH FCU. I suspect 24 channels but not sure since I never used a SBUS connection.

Hi, there are no ready made mechanics, all of them have to be customized a bit to fit. The most popular is Align 600 or 700 size. But I dont like the way they fit in the dog house so I used an RJX Vector and I'm quite happy with the results. :)

@@romeooscar8495 Tell me please. You can sell your custumized mechanics with a remote control? And if there is instructions, then I will be very pleased.) This can be discussed? Thanks.

3rd one from the top is for MSH FCU: GND, VIN, S.Port configured as F.Port or FBUS on the RF page of the tx. Not sure what connection BeastX uses (check instructions for single wire connection to FrSky), I suspect SBUS. Then you would have to use GND, VIN (+) and SBUS out tabs. :)

@@romeooscar8495 it’s exactly what I used and so far so good. I’m now attempting to program the MB FBL

I agree yes. I still fly builds that have Align mechs and I notice it right away. And SAB is so reliable, belts last forever.

Got that thanks.

You are welcome. Are you on FB? I could help you from there. 😃

@@romeooscar8495 Yes, I am on FB, send me your Social ID, I will text you Buddy

Romeo Oscar

@@romeooscar8495 Unable to find you yet send me your email we could share id link.

@@PracticalWorld facebook.com/romeo.oscar.923/

SAB Goblin 700 1st gen with tail boom shortened by 30mm. This was my only "slide in" construction using SAB, thanks to the ample room provided by the Thunder Tiger Power fuselage. It's my oldest flying build and has proven super reliable. Still has the original HDT3 (6mm width) 2004 cogs belt. The stock 700 uses a 2064 belt.

Thank you Pastor!

Hi Giovaqni, I was never concerned with range flying rc helicopter but something I will look into as soon as start flying the TDMX which is soon. I just completed a 600 size Bell 429 using it. I'm not aware of any issues thanks.

@@romeooscar8495 Thanks a lot! Very good

@@romeooscar8495 Hi, I found a serious a problem with the Tandem receiver TD R10 (2.4 Ghz+900 Mhz): the servos start to jitter / chatter strongly when I install the receiver in the fuselage (analog servos, Hitech and Emax). The issue disappears when I turn off the telemetry or wrap the 900 Mhz antenna with aluminum foil, so the issue should be the 900 Mhz telemetry. Unfortunately it is not possible to turn it off separately from the 2.4 Ghz telemetry! Does anyone know if the normal 2.4Ghz receivers have the same jitter issue?

@@giovannivitali9536 I strongly recommend your update ALL 3 firmware: ETHOS 1.2.6, the latest TDMX, and the transmitter internal module. I just flew my latest build, a Roban 429 600 with TDMX and mini servos. Works as a charm. 🙂

@@romeooscar8495 hi, I had already updated all 3 firmware, thank you

Hi, I recorded this some timeago... 🙂 ua-cam.com/video/NIDeIODFGIc/v-deo.html

Horus-rc.

@@romeooscar8495 awesome thank you

Willkommen mein Freund

Thank you George 🙂

Thank you.🙂

Buon anno e tanta salute per il nuovo anno grazie. 🙂

You would have to switch to a BeastX Larry to take full advantage of FrSky's telemetry. But I have you covered and can get you a Beastx plus with auto level you would hook up to an Archer receiver. ETHOS is very user friendly and FrSky working on the lua interpreter for integration very soon. :)

@@romeooscar8495 Thank you very much for the information Romeo! I wish Open TX took off a few years ago like it is now. I will give it some thought, I know financially I will take a hit but if I decide to change, I have (2) iKON 2 B/T FBL'S that are Brand New. Installed on 2 Goblins that I've never flown. lol. Thanks again and I'm sure we will talk soon. My best to You and Lucie! ❤🙏🙏❤