Відео

Bonjour. J'ai utilisé de la peinture automobile, une base avec un vernis mat incolore, elle a été appliquée au pistolet à air comprimé. Avant cela, il était préparé... nettoyage, ponçage et apprêt plastique pour toutes les pièces en plastique.

Un grand merci de m’avoir répondu bien à vous 👍

Hello. It can be done that way. The headliner shell is a flat surface, you can even repaint it. It will be better than being bare like that.. Good luck with the works

@@VDEdition1 Hi. mission complete.I riped this off. After take off all handles and front sun guards was probably 5minutes job. Gently came all off. Then I used wheel brush and almost all leftovers of this funny orange foam came off. Of course left some marks and I tried with white spirit but maybe it's a job for the future. Anyway on front vertical parts (where lining still is on, L and R side of windscreen) I made some brown marks from this glue/foam. What to use if for that? I though maybe Gyeon fabric cleaner, but I'm not sure if is strong enough. btw now after touch with white spirit all handles and roof lights etc. looks not bad. Creamy white handles on dark background. And nothing is hanging down anymore! Feeling successful. Tom

You're welcome.

I used Dunlop GP glue.

@@VDEdition1 Thank you sir.Regards

Headliner and pillars are upholstered with original headliner material with 3mm foam. Other plastic parts are washed, sanded, primed and painted.

You need 2 meters in length and a minimum width of 140 cm.

I only painted the plastic parts, and used car paint applied with a paint gun. Headliner and pillars are upholstered.

Hvala na komentaru. Ja sam u Sarajevu, Ilidža.

Thank you. I'm glad the video was helpful.

This old material cannot be used for repair. There is foam under the material, which burns over time and turns into a slimy mass that must be cleaned for the glue to have an effect. I used new material and thermal glue for the repair. There is a video of the entire repair process on my channel, so you can watch it. There is another car in the video, but the procedure is the same. ua-cam.com/video/cRx-KQxzMlE/v-deo.html Good luck with the works

@@VDEdition1 thank you! I'll give it a shot on Friday. Hope i dont get unlucky with all the disassembly/reassembly. In your video you make it look easy haha. Cheers!

Of course not. On my channel there is a video of the whole process of dismantling and repair, so you can watch it. ua-cam.com/video/cRx-KQxzMlE/v-deo.html Good luck with the works.

I'm glad the video was helpful.

I'm glad the video was helpful.

I'm glad the video was helpful. The nuts were so loose that they could be unscrewed by hand. I tightened them by feel, using a small ratchet.

First cleaning with Nitro thinner, then sanding and primer. 10 min. wait for the primer to work and then you can paint. Good luck with the works.

@@VDEdition1 thank you very much. Wich sandpapir did you use ?

Do not use coarse sandpaper. I used Scotch-Brite Hand Pad - gray

Thank you.

Saraievo, Bosnia și Herțegovina.

This particular car does not have it, but there are models that come with that option, a panoramic roof.

A mirror holder that goes towards the glass, you just rotate it.

@@VDEdition1 Thank you :)

40 seconds into the video and maybe to you this looks like a struggle, but in essence this is outsmarting with plastic over 20 years old, "How to take it off so it doesn't break". Nothing is broken in this and hundreds of other cars. All customers are satisfied. And my favorite are the comments of you characters who have 0 content on the channel, but thanks in any case.

I'm not sure there is any other option if there is no cord.

This video is more based on how to remove the headliner. There are other videos on my channel where I show the headliner repair process itself. Thanks for the comment.

I'm glad the video was helpful.

I'm glad the video was helpful.

THX :)

I'm glad the video was helpful. Thanks for the comment.

I don't understand the question!

Thank you.

Thank you for your comment. You don't need a lot of tools. Torx screwdriver tx25 and tx30, Flat screwdriver for removing the headliner, and for panorama panels a 10mm ratchet is required. It is important for the adhesive to be heat resistant. I used Dunlop LP. Good luck with the works.

@@VDEdition1 Thank you so much for your prompt response. What did you use to turn the slider motor while removing the slats?

Thanks for the comment and advice.

Hvala na komentaru. Kao što sam naslov kaže, ovo je video o tome "Kako ukloniti krovni tapacirung iz auta". To sam i snimio do detalja, a koga zanima cijeli proces reparacije, ima na mom kanalu videa koji obuhvataju i taj dio. Npr. ua-cam.com/video/cRx-KQxzMlE/v-deo.html POZDRAV

Thank you for your comment and good luck with your work.

Yes, I did use polishing paste. The most ordinary polishing paste is sufficient.

@@VDEdition1 thank you, i have this exact same issue, chemical burns either from interior cleaner or UV protection. last question, what kind of polishing pad u used?

Den Dachhimmel und die Säulen habe ich mit neuem Material mit Schaumstoff gepolstert. Und ich habe die Griffe, Lampen und alle anderen Kunststoffteile lackiert.

Unfortunately, it is very easy to break them because the plastic becomes brittle over time.

I didn't take it off. If you have diagnostics to delete errors after disconnecting the battery, you can remove it, but I say, there is no need.

@@VDEdition1 okay, thank you, i was worried about airbag in the back

Thank you for your comment.

I used the black base CODE 041 and painted everything with clear varnish.

Samo veselo :D

You're welcome. I used plain black, although that's a matter of taste. A lighter shade can also be used.

You're welcome. Good luck with the works.

I used a black base, CODE 041 +10% white to soften the intensity of the black. I cover everything with matte varnish, although it is not necessary. If the plastic is properly prepared, washed and primed, then the base itself will be quite stable.

No need :)

@@VDEdition1 OFC there is no need, but it would be better for your videos... Remove all VW

Dunlop LP

@@VDEdition1gde ga mozes kupiti... Dali bi bio pattex universal classic dobar ili ne za taj posal...

Fabrički je iz dva dijela, ali su zalijepljeni i nemoguće ga je rastaviti da ga ne uništiš.

@@VDEdition1 evo trenutno sada presvlacim nebo to, nisam rastavljao nego iz 1 djela presvlacim i bice dobro.

You're welcome.

I'm glad the video was helpful. Greetings to Brazil from Bosnia and Herzegovina. Good luck with the works.

I'm glad if the video was helpful.

Thanks anyway for your comment.