Відео

Thanks bro 👍 good job. You re awsome 🎉

C480W. Great Video. I need one Hour and it works 🙂. Thank you very much

I got the white tab out but now it wont lock back in. Any suggestions?

Thanks for this extremely useful video. Samsung didn't design this printer with disassembly and repair in mind!

Thanks for sharing this. I was able to fix my printer following your instructions. 👌👌👌

Great video and very helpful, BUT! It needs either audio or captions. At the 7:30 mark, when installing the plastic part that caps the black tube, if you don't have it aligned just right, you WILL rip the tube when snapping the piece on. No second chances there. Then at 11:25, when installing the large white connector, care needs to be taken as the terminal in the strip can be sticking out a touch, and simply pushing the connector on will once again, put pressure on that thin black tube. lastly, one that drove me nuts is at 11:37, when reinstalling that shaft, the eccentric on it also has a pin in it. If your not careful, it will fall out while the shaft is on your bench, and you will go nuts trying to figure out where it goes! However, I wouldn't have been able to do the repair without this video so thanks for making it!!

thank you for sharing this video. i fixed my printer with your help.

After doing this my colors started printing offset from one another, like an old 3D book. Any idea what I did to it?

After doing this, my printer started printing the colors slightly off from one another. Could that have something to do with that little white thing you use the tweezers on? Any idea what I messed up?

This video saving lives years later

Did the steps but transfer belt isn't moving any cm? 😥 This Video is better: ua-cam.com/video/1xoh7YaOwkA/v-deo.htmlsi=z8J-PZeQ-FiS4OU0 Wasn't aware that the lock on the left side has to be pulled so far to loosen the belt 😊👌

Hi sir fuser element ko ko meter ka Sath contibutiy ma rakhe ker check kerna ha

Thanks specifically for the fuser teardown instructions. HP doesn't want us to actually repair fusers. With your help i managed to replace a torn preassure roller (orangy thing) and now it prints like new. Cheers.

Thank you

Thanks for this extremely useful video. I was about to bin my SCX3205W for this very problem, but thought I'd give the repair a try after finding your channel. I found I didnt have to do as much dismantling...just removed the left hand panel. Solenoid was really sticky...I replaced the black patch with a piece of heat transfer rubber for a TO220 transistor mounting kit...now works like new. No screws left over! Thank you!

Adorei doque vi

FUSER for 120VAC and 230Vac are same ?

I see in your information about you, you are in India. Do you have any associates in the UK? I have one of these printers with a problem and I'm not too confident with dismantling it!

How on earth could you disconnect the dev. Unit connecter, it is tightly connected there and wires might be damaged if forced.

i need the driver software of DGlogek TP - 3040, can u send me please

New model and basically you have to open up the whole printer. Older model you could remove it without touching any other parts

mine still has lines and i cleaned It perfectly

uhg, too much work for what should be a easy repair......

Mere bhi printer me power supply nhi aa rha hai tik tik ka avaj bas aa rha hai solution btao

j'ai pu réparer mon imprimante, MERCI beaucoup

Have you ever done the paper pick up solenoid

Blh tak nak minta tlg repair saya punya printer

Best repair video ever! Thanks. I could fix my printer Samsung Xpress C460W based on this video. Almost all parts are same, only difference was that my printer did not have the ethernet panel, which is on this video, but all the rest was the same. I did not need to stick a pencil eraser, as in the video, but I could stick the same rubber back, as was there. My problem was that the rubber was slightly wrong positioned. After I positioned and sticked the rubber more to the side as it is in this video, that fixed the issue.

Nunca compren impresoras HP tiene una politica dictatorial con sus torner ya que con una actualizacion que hicieron a todas su impresoras ya no pueden usar otras marcas ni volverlos a reulilizar y no compren este modelo yo lo tengo y es muy dificil de manipular, cuando se traba un papel en mi caso ya no la he podido usar para imprimir solo escanerar , pero no es lo mismo asi que ya saben no compren Hp e indaguen cuando quieran comprar una impresora laser multiuso .

Same problem. Thank you so much for the tips. 😅

I have the same problem, samsung printer design is the worst

This was super helpful, thanks. Fixed my M255dw. Same process except for one additional screw.

thank you saved me !

What happens if both cuts on the wheels do not match? Engine problem?

Very similiar procedure to the M281 HP printer. I just used this video for that printer.

I watched this film and it didn't help me but I'll leave some info for someone who probably encounters same problem. No foreign object - grinding noise on start and constant paper jam near OPC shaft in the cartridge. Usually people recommend swapping whole paper feed assy RM2-5715 because it has motor in it and that's expensive. That printer had 227k pages printed, whole gears in assembly were fine except the gear on motor RK2-7103 which is made from very soft metal, all teeth stripped, you can damage it even with screwdriver, very soft. I have replaced it with gear from motor of some konica minolta made of magnesium alloy - way harder than what HP used here, had same teeth profile and overall dimensions, could be pressed on the original RK2-7103 motor and aligned. Printer works.

Thanks a lot! Mine's working again now!

Great video!! Having same problem with magenta . It says 90% though. And when print supplies status black dots are not perfectly aligned. Any idea?

Thank you!

is this model same with Canon MF631cn?

I better buy a new one than watching this 16minutes video😅

Worked perfectly!

Thank you it helped me in my new job 😅

What did u do?

Thanks a lot, u save me a lot of money ❤❤❤

Idiota el que filmó

Thanks - this video was a great help as I had paper stuck.

Where are you located. I would like to send several scanners to you for repair.

A4-200

BUENAS NOCHS, MI IMPRESORA MF8280C NO TOMA LA HOJA