Відео

I know its two years but any tires still available? I'm trying the spacers out tomorrow

Thanks for saving me thousands in repairs

Excellent video sir

How did you do the white pinstripe on the bottom? Thats a great looking board.

Where did you guys find those rim weights? Normally you reduce rotating mass,can you notice any difference in acceleration or punch of the car?

Depends if you are used to backing using mirrors or those who look over their shoulder

Good video, I run INJORD Brand Inserts Green- on 7 pound and down weight crawlers and run the blue inserts on 8-pound crawlers and up and don't get any tire roll like in the video that's almost always caused from inserts to soft.

How much to have you make two motor skids

Is it too let to get some free tyres 😂😂

Nice video Boris...do you still run lcg skid plate on the trx4?

Merci vous m'avez sauvé.

Great.. thank you sir now my camera functioning

Great lookin jeep!!

I found that if you use default code on door lock switch on driver door cetral locking system that was on wire that door key lock. You could simulate entering the code 1515 left to lock (1) un lock2nd digit 5times right then lock direction(1) then right again (5) times .urdone light on dash shuts off immobilizer disengaged

Sweeet trail run.

Spot on! Solved my problem without having to deal with BS tech support.

It didn’t work for me, the white cable is for changing the coding of the video output, how can I solve it?😣

youre seeing it wasnt that great of a adjustment. im running a sport high trail pretty much stock with the limiters removed and 30 wt oil with a 1080 esc and a tqi radio with the link module and receiver. removed the crap on the cage and got the shock rings right where the spring doesnt leave the bottom but soft as possible. removed the front and rear bumpers and flipped the mounts up. shits a beast and follows my comp rig well. that rake will send you end over more than not. especially on your descents down hills. flat rock gardens as we see does fine. any real incline with crawling and weight transfer its gone.

Hi very nice rig but the rear shocks don’t work very well in semi-droop change your rate spring with soft medium(lenght)spring under piston and medium short spring upper piston and 2 hole piston with 30wt oil

ADD FOAM NEXT TIME LMAO

Looks good. Question, what material did you use to print it and how is it holding up?

Bitchin' 😂🤙✌️ to use a 80's term 54 yrs old just got back into it with 9'4 Gerry Lopez Long Haul. I understand the term pop out now but try to get a real shaped board by those still doing it the right way. I'm on a waiting list for after summer sometime, uff. Still thoroughly enjoy being the water fer sure. Scratch my head why I waited so long to do it but when it takes 2-3 days to bounce back from a sesh, I know why. It's worth it though. Surf bum now 'til I croak...🤙🌊🙃

getting out of the water looks a challenge for us oldies. Gone are my days of rock skipping.

Awesome!😊

Good video 💪

Thanks...But cutting the green cable should eliminate the grid lines..and you still have them

💪💪💪🛻🚘 strong Jeep , good machine men 👍👍👍👍

Not sure about the guy you met, but I added all chassis alloy, f/r bumpers raised/tucked, 2.2 beadlocks w/mudslingers, long arm kit, 120mm shocks, axles and all brass down below -except those cheesy bolt on and wheel weights🤮. Absolutely zero issues so far, except when it does decide to roll and on a steep hill GRAB IT!! Very very heavy 😅. Made my trx4 unstoppable on the trail and creek's though. Tire foams that are the right size and density (med+) are crucial. Tuning with good shocks like desert lizard is also so important. Love my first trx4 build💟 will not be my last.

Tenerife, Island in spain

Where in world is this located dude?!

Any thoughts on over riding for the 2002 Land Rover Discovery 2 - I changed the ignition because the key broke in the ignition, once I changed the batterie in the key fob the fuel pump stops due to anti theft.

Love the throttle gizmo, buddy. 😊

Link is broken unfortunately...

Look into furitek python x esc. Your motor will run super quiet and smooth. You’ll love it.

really cool rig but what is that chassis? Never seen anything like that

Hi! Great! I have ONE! I Lost the remote control.

Salut my friend super car super video subscribe subscribe .

Nice rig, buddy. You're going to mix it with the big boys now. Enjoy!

Not bad for a new rig on a new course just a little more will time and you’ll have it up

This place looks amazing 😃

Nice 👍🏾🔥

Flipping sweeet thanks for sharing a killer comp with Awsome rigs. I wanna comp there. Making some dinner to this perfect

Nope. No loop in my cable.

I might need to look into getting a 3d printer and try one of those skid plates👍 great video mate thank you

cool vid, my friend! appreciate the views number! keep it up! big like! 👍👍👍

Yay, go Homer go lol

I have about 4 now but I recently had one stop after it became to hot I’ve never ever had a brushless motor get that hot ever I can’t figure out why I hear gearing can cause it.

You can not beat the fusion!!!!

cool new look, RC with great adventure, always good videos bro👍👍😃

12:17 your charger said it was a 3s battery, at least thats the setting you had it at. either way your not running a 1s so no 3.2 volts is WAY to low for the battery unlike what you said. or it was actually set at 3.2/cell. either way i highly suggest you stop playing with lipo batteries until you educate your self on them and the settings in your esc.