Відео

I'm in this situation, and will check the back out. Watched another video on a possible solution (left side drainage clogged). that wasn't it. mine sounds like it wants to run, but then back to blinking normal and the chime notified. stay tuned.

Samsung stinks & will never buy another appliance from them. I had a $2800. refrigerator that died in 4 years bc I stored it for a summer in storage and the so called earth friendly foam insulation degraded and therefore the condensation built up when plugged back in and killed it. The chemicals in old good foam insulation kept foam from being so sensitive to temperatures changes. I guess another appliance being in the dump is really earth friendly & green……so stupid and when will people wake up the the nonsense that seems to be motivating this stupidity.

The leak sensor is that round assy with the two wires hooked to it in the bottom tray. That’s what makes the normal light flash, it detects a major leak. It’s a Styrofoam float. The two things you called sensors with the wires hooked to them are the ends of the heating element. the impeller with the bad oring is the drain pump. Mine was leaking I believe from the same place. I’ll never buy another Samsung Dish washer.

Sounds good

Thank you. I’ m having the same problem and the dishwasher is 2 weeks old

Where's your other videos when you did the repair?

This was also the issue with our dishwasher; that O-ring isn't rated for heat. Replaced with an Imperial Supply O-ring, part #70081, 51 mm ID, 57 mm OD. Hope this helps someone... and this is also the last Samsung appliance we'll ever purchase, as our Samsung refrigerator has had multiple issues. Never again.

I don’t see parts 1 and 2 😢

I doubt it was the o ring. I have been repairing appliances for 30 plus years and have never but 2 times had to replace an o ring like that.

What you pointed as moisture sensors are not that but are the heater connectors. The moisture sensor is in the big round plate on the drain pan with wires connected to it.

How does one separate the impeller from the housing? I’m trying not to break it.

their CHEAP CHINA CRAP....

Where do you find the "O" ring. All I can find is the pump.

Holy smokes you were brilliant 👏 and such a great band. Let me know when your playing again?

where do you buy the "o" ring and what's the name of it?

This works for me. I just cleaned up this small moisture detector. I wiped it with a Clorox wipe and then paper towel, and then use a air dryer to blow it a few minutes. Putting everything back, and it works again. Thank you!

Just did this repair and found a slightly thicker /smaller o.d. o-ring that worked great. Size: 2 x 2-316 x 3/32

Where did you buy the oring

Did this work?

is there a way you can show us how to disassemble that and replace the o-ring? and without all the shaking of the camera phone...LOL!!!!

This dishwasher has been a nightmare. You are right, the built quality is horrendous. Thanks for the video

Where does the O-ring go ??

That was it, greatly appreciate this, thank you truly.

Atta boy Darryl!! You rocked it !! Man this band is a dream team !!

where did u find the o ring , i cant find one

Yea piece of shit. Mine is 6 months over warranty. Water valve leaked. Fixed it, now won't work when u hit start. The one it replaced in 2019 was from the 80s. Time to call someone i guess

This happened to my Samsung dishwasher as well, about a year into use. Thanks for sharing!

Ok I just purchased a new dish washer, so I'm trying to install it, the normal light is blinking , so how do i get to the O ring, under the bottom or what

where is the o ring located

Same issue and model 3 years in. Can you update us to whether the issue is resolved 7 months later and provide the o-ring size.

Same model, 3 years old and it failed. Samsung makes poor products. Never again.

Hey buddy can you please let me know where we can buy the ring. I have a same issue thank you

Samsung is trash

Thanks for the video! Mine is doing the exact same thing. I will pull it out and dry it out.

Would be awesome to see how you took that piece apart to get that o ring out to replace. That’s where I’m stuck. Any chance someone knows of a video out there somewhere?

Where do you get the o-ring???

Thank you, I have the same dishwasher. Doing the same thing. I will check the O-ring.

Thank you for the vids and information. Our Samsung is doing the blinking normal light thing as well. I haven torn into it yet by will. Does anyone make a high quality dishwasher? Bought a top of the line Kitchenaid several years ago. It worked great for 6 months. Then even after multiple services and a motor and pump replacement, it still did not function. I bought the Kitchenaid because it was Made in USA...

Thanks for this video, man. Mine is about 6 months over the 1 year warranty and the damn O ring took a shit too. Going to replace it tomorrow with the help of your video.

Thank you very much man, I’m having the same exact issue, much appreciated!

Great job explaining the problem and solution.

I was having this same issue. Luckily, Harbor Freight sales o-ring kits for $6.99 and I had one. I had to upsize the diameter of the o-ring but it felt better when I reassembled the unit. Put it back together and ran the dishwasher. Running well. Thank you for the video!!!

looks like that I have the same problem. What exact size is the o-ring? thank you for posting the video. mine is one year and half old.

5 or 600 hundred dollars, sir.... that is a lot of money

ok folks i was having the same problem for about three weeks, so i found on UA-cam everyone's remedy to fixing the problem. Me being 60 yr old women not able to take this thing out and apart, so i decide to get my wetvac remove the screen from inside the washer located next to the water wands, and suck out what water was left in there, about 6 minutes, then i placed my small garage floor fan in front of dish washer, and in about 10minutes everything went back to normal working fine.

same dishwasher,,,,always winnning on start,,,,was the pump impellar came out of the shaft just enough to rub on housing causing pressure on housing making the seal to leak.....drip down on drip safety switch..... had to glue impellar in place...problem solved

We have the same appliance and seems to have the same issue. From where did you get the “O” ring? This thing is just a little over a year old and started giving issues compared to the original 20 year old dishwasher which still worked when it got replaced.

Epic now I will check that piece so far was a side screw that was leaking and it went to the same foam on the bottom really bad design never againg buying from that brand.

I love the PBR on the counter. Thanks for the video.

So, I had a small leak coming from the outside of the slider bars, one of the hex nuts had undone itself over time, I would highly recommend tightening these, there's nothing anyone can do about that one though, except for locktite.