Відео

My SuperGlide jaws are jumping away from the tooth track preventing the jaws from opening and closing. Can you provide a solution please?

If your pitched at 90 degrees your not moving the trailer straight back. Why would you get yourself in that situation.

Nick what do I look for in a used fifth wheel hitch?

Any advise on a curt slider? Mine has that same movement and chucking

Terribly biased review. I owned the Pullrite and used it tow an 18k lb Toyhauler, worked great and didn't have any concerns. However, you absolutely could have done a 90 degree angle with the Anderson and most likely would have had the same space as you did with the Pullrite. Then you talked about the height issue with the bed rails. Why not raise the ball on the Anderson?? It has the ability to do that, just decided to move right past that? Frustrating that I came here for an honest review and didn't get it, what a waste of time.

Orrrrr….dont be a dumba$$ and just buy a long bed and the lightweight easy to remove Andersen hitch like me.

As limited as the Andersen turns, it's still better than a travel trailer...

If you do another video. Add checking the torque of the castle nut on the hitch roller and the condition of the roller washers and the roller sleeve to annual maintenance.

I appreciate the review l, but it would be so much more informative and balanced if you would have filmed both of them showing corresponding clearances while actually maneuvering. Doing it for the Anderson and not on the pull-rite leaves the viewer wondering why the really critical segments were left out ☹️

Tell me you are sponsored by Superglide without telling me you’re sponsored by Superglide. 😂

Superglide, good hitch but don't even think about taking out of you truck bed by yourself because it ain't gonna happen. Thing weighs too much!

I appreciate this video on what to check and tighten. Question for you: I want to raise my 2900 Super Glide and see there is a kit to purchase where the hitch can be raised 1 1/2 of an inch. I'm trying to make sense of the pics on the web site. Will this work with the Ford puck system?

Just bought that hitch in the 2714 model. But I have heard backing up with this hitch is a little different. Never owned a 5th wheel before but have towed quite a bit. Looking for a vid on backing up with this slider hitch and it is very hard to find.

Thanks for the video Nick

Tips for hitching and unhitching on ground slightly lower or higher, truck vs. trailer.

I’m looking at the super glide but my parking spot is at an angle with the truck lower than the trailer. Will I still be able to un-hitch?

Well I probably will never go any bigger, however I did go ahead and get the 20k model just to be on the safe side

I have a 2022 Chevy Silverado 2500HD that has a 6ft 7in standard bed. The 5th wheel I’m getting is a Keystone Cougar that has what is called Maximum Turn Radius front end. Would the PullRite still be the way to go?

Good hitch, but you better have 3 other guys around if you ever want to take it out of your truck bed.

Hi Nick thanks for all you do for us out here. I have a question for you. I'm thinking about swapping my b&w slider for a super glide. My 5er is just over 14k. I have the option of a 16k or 20k hitch do you recommend just going with 20k?

Great video. Just recently watched a video from Irene Iron Travels when they reviewed and showed your help with the install of the pullrite auto slide. I have a 22 ram 2500 and it seems the only system pullrite offers for the ram puck system is the 24k lb which is significantly more costly than the 16k version offered for ford and GM. Is there the lower capacity option for ram? Thanks

That’s why it’s better to Look for A Truck with 98” (8Ft. bed) Not the 6ft.Bed

Idk what this is but god bless you and gis bless America may the algorithm be forever in your favour

Extreme crismas tree stand

I have a 2015 Ram 3500 with Ramboxes. Looking for a safe setup so as not to contact the ramboxes. I have the BW turnover ball installed. Will the PullRite Superlite work with my setup? The trailer we are looking at has a Morryde Orbital installed.

Nick if I install the bolt I can't just push the arm down I would have to use a C clamp to get the bolt in I think it to tight

I like how you didn't show the loading of the super glide. Definitely seems like you have a bias against the andersen. Curios if you have tried the reese goose box?

Those plates look like spacers

You can and could have done a. 90% with and Anderson. I've been using Anderson for years now and can use to have to do almost a 90 to get it into where I park it in my driveway and it's not even and I have a slightly steep drive and have probably 6-7 inches between bed and bottom of trailer and have gotten into several tight spots with zero issue with my short bed f350. Also I don't need 3 people to take my hitch out. I can also haul more things in bed because of the open design. Must make more money off selling the pull rite I would guess...

I love mine. It is so easy to clean and maintain.

I’m not sure why you choose to not use the Lippert installed Turning Point swivel hitch that you paid for when you got the Reflection 260RD trailer. I see it installed on the trailer in the video. You could unlock it by taking the two bolts out of the back of the pen box. Then reinstall the wedge in the hitch up by the pin, that you had to remove to make this video. Then use a cheap Reese 18K hitch in the truck. The turning point hitch will allow as much as a 90 degree turn, and made for lightweight short bed trucks.

Even after several years, this is still a good video to watch and rewatch as a refresher from time to time. Thanks again.

Thank you for the informative video!!!!

This is a good hitch. Don’t get me wrong and I own one. But it is absolutely not good for tight quarters because you have to have your truck and trailer straight in line within just a few degrees or you can’t unhook or hook back up. After living with mine for two years, I would definitely just look for a tow vehicle with a long bed from now on.

Great video. I went out and checked my hitch, everything was loose. I made the proper adjustments per your video. The large pivot bolt was dry as a bone. I greased it up good and and tightened it up to your specifications. Thx again

Hey Nick the rocker arm springs back and the nut will not tighten. Looks like the spacers on either side of the rocker arm are worn.

Thanks for the video. Do you have a link to the 2710 shims? I do a search on the Pullrite website and other websites and nothing pulls up.

Thank you Nick for another great video. We are very happy with our SuperGlide and would recommend it to others.

Hey Nick I have a question for you. I usually use red lube for the hitch and the plate so it doesn’t scratch but I noticed in one of your videos you just use WD-40 on those areas as well? Will this do the job as good as the lube without the mess? I wish I could use a plate on there as standard hitches with no mess but I don’t think it works that way anyways well WD-40 work. Thanks.

Ok so the main thing I’m taking away from this video is that ford made a short bed dually! I need to find one of these asap lmao

Thank you for this video! Very informative to a newbie 5th wheel owner like myself. Ironically, I had already chosen the Super Glide but your video gives me that extra confidence.

I own the super glider hitch the disadvantage is you can’t disconnect the hitch at extreme angles or connect at an angle. You can’t get the capture plat to engage with the hitch

Where does a person purchase this particular capture plate pullrite 331723

Looking forward to trying it out! Currently running the single point 3900 series. Been interested in this for over 4 years. Gregg 2022 Silverado 3500 High County 2022 Jayco NorthPoint 310 RLTS

Another great video Nick explaining important features on our hitch. Along with this hitch, would the trail air pin box work with and be compatible with the 2900 Super Glide while preventing some of the chucking during travels?

I love my long bed F350

THANK YOU FOR A GREAT VIDEO ON MAINTENACE OF THE SLIDER HITCH. (FYI I TYPE IN ALL CAPS, NO YELLING LOL) HITCH HAS BEEN WORKING GREAT BUT, WHEN WE WENT TO HOOK UP ON SUNDAY WE HEARD THE LOCK SNAP SHUT AND MY WIFE SAID TO STAR TUG TEST, SHE YELLED STOP BECAUSE THE KING PIN WASN,T IN THE LOCK ? I MISSED IT BUT IT STILL SNAPED SHUT LIKE I WAS IN THERE. THIS HAS NEVER HAPPEN BEFORE. (WHAT DID I DO WRONG ???? THIS IS ONLY MY 4 TRIP OUT WITH THE RIG. HAS ANYBODY ELES HAD THIS HAPPEN WHERE IT SNAPED SHUT BUT YOUR KING PIN WASN,T IN THE LOCKED HEADS???? ALL COMMENTS WELCOMED DAVE

I love my Anderson Hitch. Worked unbelievably well with My 2021 F350 short bed even with a bakflip tonneau cover and a aux fuel tank. I now have it in my 2022 F350 long bed. 15K miles and smooth as silk. Great video and info! Towing a 20K Redwood 37" fith wheel. SOOO easy to remove, and replace. 5 min tops and really light

Discovered these over 15 years ago,, & inittially decided one of these would be mounted in a Ram truck someday,, when we finally decided to get a 5th wheel & hit the road full time. Well,, 15 years later,, we are getting real close to getting a truck & 5th wheel,, & ''still'' looks like the Super Glide is the ''no brainer'' way to go. 😉 Don't understand why its not in the current ratings though ?? 🤔 It is a super slick ''stout''design,, & am saying that fom being a Mechanic/ fabricator most my life. I

Great explanation. Very happy with our PullRite 2700.