Відео

Well. Basically are but he provides the 3 inch maf housing but you can always get the maf housing for an extra $50 if you wanted !

THANK YOU BRO 😘

Works same way with data

Yeah I’d say so as well 😅

If you care about weight reduction and trying the best to get better times then yes. That’s what I’m going for other than that any y-pipe does good they have different tones and sound that they will give due to the material.

@@drivermod1 which one do you think has the best tone

Yessir 💪

🫡 have to! I honestly haven’t ran into any besides the fuel cuts but got rid of that with the hydro mat ofcourse. It’s been very surprising

No no you want it facing towards the bank as the gas goes there when you are stepping on it passenger side fuel tank

At this point 🤣 but he did have injectors, full e85, drag pack over me 🥸

I’ve had it for a bit now tested and after just 1k miles it already collected the oil and a good amount as well.

@@drivermod1 😁💪🏽, me convinced. Thank you my good sir!

I bought heat shield wraps from Amazon and zip tied it on (I know exactly what you mean about the location being weird too)

Yk 💪👀

💪💪

I did 2nd gear for 40 but wasn’t paying attention that run and the rest I was in 3rd gear one I was in 4th don’t remember which roll tho still have to get used to the tune

U

The q60? It’s fbo just no injectors and not full e85

Unfortunately no I don’t have the tire to do so 😅

I used the heat wrap from Amazon

Thank you!! 🫡 and not a problem at all I’m happy with them

You could but we just did it this way 😅

@@drivermod1 okay I was just asking because I’ll be doing the install this weekend lol

No you won’t as long as you don’t have it in the tank over 2 weeks

Yessir 💪

I was already tuned but if you are untuned it will start but driving it definitely not recommended (from what I heard)

I’m glad to read this seriously I appreciate it 💪

Thank you 💪

I do not have any blow off valves and yessir definitely should try it! 💪

😅 it’s sketchy for sure

👀 something even better is cooking

I answered! 💪

What seemed to you?

Yes pride catted down pipes to tomei y pipe tomei exhaust

💪💪 thank you!

^^^ this is the best information on this product and very true thank you b&c 💪

@@drivermod1 Absolutely! We have installed at least 100 of these on Qs. They are superior to anything available.

@@bonnieclyderacingthat isn’t the main problem on this problem. The main problem is excessive positive crankcase pressure, that destroys the turbo seals. So how do you solve that? You vent to atmosphere under boost. Use check valves to do this. Significantly better for the car. How do I know this is a problem? My oil dipstick popped out and splattered oil everywhere after a hard drive. Either the oil dipstick pops out, or the rear main seal, or the turbo seals. After I did the system which cost me a total of 70 dollars with Amazon catch can, breather, 3/8 hose, and 4 check valves that no longer happened.

@@2seep It literally says in my comment “significantly reduces crankcase pressure” I’m well aware of the the issues with crankcase pressure, we developed a monitoring system on a couple of our cars we have added pressure sensors to the valve covers to monitor the system and are developing a billet vac pump replacement wheel to increase vacuum. We have been using this catch can since 2021 on customers cars specifically to fix massive smoking from the turbos due to the issue. We have helped at least 20 customers over the past few years get their cars back from Infiniti without spending thousands to replace “blown turbos” we figured out the excessive crankcase pressure issue immediately and fixed it while other shops tried to convince customers we were wrong…. Well it’s ironic now all those shops are doing the same! Lastly this product is listen on our website with a much more in-depth description then the one I left above explaining how it solves crankcase issues as well as multiple TikTok and YT videos we released about it. We even wrote a long detailed explanation post on VR30 Drag Racing Development FB group about it a few months ago. We have been at the forefront of teaching customers how to protect their engines, EVERY big turbo build we do is required to run this catch can for these reasons or we will turn the install away that’s how serious we take the issue.

Seems like a hell of a lot more work than other catch cans. 🤷🏻‍♂️

Haha 💪

💪🫶

Thank you! 💪💪

💪💪yessir and message me on Instagram and we can make them for you and not costing you an arm or a leg 😎

💪thank you my guy also everyone check out his page as well! Very useful information he has!!! ^^^

Me like 2

I just used adjustable wrenches

I did it before turning on the car and kept it open as it warmed up and made sure no bubbles came out

I got it from Amazon some adhesive heat wrap

Couldn’t agree with you more 💪

I was in second gear around 20mph I guess I didn’t pay attention and it started to swing 😅

@@drivermod1 you ever drift it? 😄

For real 🤣🤣

I have a redsport I did it no tune I was fine I even stepped on it a bit no issue just don’t keep doing it until you get a tune!

@@drivermod1 ok bro , did you notice any performance gain