Відео

Was all excited when I found this video as I have sash windows, some three storeys high. Then realised my Victorian ash windows have no side screws! So not as simple. Back to drawing board! ☹️

The best video. Simple. Thank you

any recommendations what to use as primer/undercoat and paint? my window paint is flaking off badly after they were done with water based paint 6 years ago...

It hurt to see you paint over those pulleys!😢

More like an extended advertisement than a How To (as I was looking for). Not enough detail for a How To, on top of which there are often non-narrated subtitles speeding across the bottom of the screen at the same time that there is not one, but two or more demonstrative video clips running. How to watch two+ videos AND read subtitles at the same time, I don't know! ...if I were that much of a genius, I'd be making enough money to be able to afford to pay someone to fix my windows for me! LOL

Not impressed

Great job, and great walk through. About to try my first ones today. Wish me luck!!

Bit of a rough job by the looks of it, filling & sanding isn't going to give you a decent finish on inspection. I came to the site thinking it would be about renovating & double glazing an old window, this was just bodging.

Great stuff guys. Where do you get you beads from? Richard.

should have used, or specified using linseed oil as primer/undercoat/paint etc

True professionals. What a great job. Looks so nice. Well done!

Clear & concise thank you.

5:30 Always use the worst, oldest brush in your kit & over brush, brushing the material until dry so the finished surface looks combed & stranded. omg & wtf from Chicago, Il. U.S.A.

Excellent. Thank you. Here's hopg ths wll be as straight forward as your video looks. 😎

The paint job was done horribly i saw him painting little bit of the glass and the pulleys thats shame

Paint should be stripped, and fillers should be the flexible ones. Otherwise all great,

For this type of window, especially for cleaning they should all be fitted with what is called the Edinburgh Hinge, simple device

Live up in Edinburgh and needed to refurbish my sash and case windows. This video was just brilliant, thank you for making it. I’d love to see more.. perhaps how you go about making new sashes and the joints you use.. I see some use dovetail which is no doubt great for strength but requires much more kit than a tenon. Other thoughts would be re-roping vid, routing out sashes to take double glazed panels, restoring warped shutters, making new shutters.. the list is endless and this vid is so clear I’m sure you’d nail the other videos too!

Hi Gary, thanks for this. This is an excellent and very informative video.

The lower sash of some of my windows are wobbly and I was thinking, while I realized that these can be easily removed, is it safe for me to reinstall them a litte bit further, so to stop the wobble and consequently reduce the air bleeding gap? I would then put a line of sealant just to make sure there arent any further leaks from the bead and the frame.

u guys are fucked if thats lead, which it probably is

Hello Gary,what kind of money am I looking at paying here in England for that work on my Windows ? Same sort of size

Sorted! Cheers.

That's just rough needs new sash not car body filler no way!

What area are you based?

What about security if these type of windows are on the ground floor..... I reckon a burglar could just push them as the wood for the sliders is just doweled in.

Thank you Gary

Uh did he just screw the staff beads ?

Thanks a lot 😀👍

Brilliant video and brilliant job. Thanks.

I love this job when everything is going fine but on the most of the cases it don't :P I also use this black 1pound snippers they are the best You can buy like 5 instead of one which gonna wreck sooner than this five anyway :) I also suggest to use rubber mallet for bead's job. Nice movie and good job, regards.

I have a window that is rotten 5 inches up the sides so I had a whole new sash made and 2 pieces about 18 inches long jointed for the corners. I don't know if that makes sense but basically, I'm trying to replace the lower fourth of the window and I'm not sure the best method to join it to the upper 3/4ths of the window.

WOW, Fantastic job, so quick, loved the video, many thanks from Australia...........

Have been so scared to take out my sash windows as wasn't sure how but going to give it a go as your video is so clear

Nice one mate, thank you.

I'm curious why you didn't prime prior to reinstalling the glass and reglazing.

Super awesome! I second the question about source for the clips and brushes. Also, what were you using for the wood repair? I've used a two part wood epoxy, but it is a pain to work with and not as fluid.

you can also get a storm window

You forgot to put glazing points to hold glass. Just putty will not work.

Hi Gary. Great video, thank you! What is the name of the drill attachment used at 4.31 please? My replacement parting bead is too large for the groove I have.p and that looks perfect to help widen the groove.

Beautiful...now jump over here to Canada...ok...

what do you do to remove the old lead paint on such windows safely?

What a shit job! I think you better pack in the tools kid!

Can you give a source or manufacturer for the retaining clips and or brushes & carriers?

Great job start to finish ! Would be nice to list all materials used.

I wish you would work in canada !

Old window is best than new replacement window

Are you based in London?