Відео

Can you share costs? Concrete, building, install?

I got S130 2years ago, about 30hours on it. My fuel gauge just failed on me, I heard because battery inside is low or bad. Anyway owner has to buy a new gauge and it cost $75, since the battery cannot change DIY.

I don’t get sloping the slab side ways for drainage. It’s inside. It shouldn’t get wet. If you’re going to wash inside then maybe slope towards the door would make sense.

Those trees are Crape Myrtle

How do you turn of the parking brake and also the clutch brake on mine is stuck for some reason can you help me

Bro i got one the 2 days ago and its so good

I’m an inspector for a living they would hate me 😂 especially because I’m Hispanic.

Holaa llave paso de nafta hacia abajo como en el video esta abierta o es reserva?

Hey great building! I’m looking to do a similar but with a 6” slab throughout. Did you have any issues with the slab cracking around the edges where they put the anchor bolts in?

Great info! I wasn't aware until I came across this video

OMG, I drove a ground rod in with a sledge. Took forever. Thanks for showing that. We were considering a steel building, but I have seen several videos that showed too many problems.

You got white smoke so there's not good flow get the good flow and you will stop the leaks without sealant.

Seasoning the inside of the fire box is a waste of time but the V in the fire box might be something to check out.

The proper smoke should be almost invisible or just a little blue. If it's white that is the wrong type of smoke. If you see light that does need sealent.

If you have proper flow thru the smoker there is no need to seal the smoker. Leaking smoke is a sign of inproper flow.

Nice work - did you use wire size 2-2-4-6 wire of 2-2-2-4 MHF wire ?

Thought this was a review of the lights! Instead it about you talking

Thanks for sharing this! I’m planning to do something similar for my detached garage. I’m considering stubbing the conduit up through the slab and into the wall. Is there any reason you didn’t do it this way? Is it just because it would be cumbersome to coordinate the conduit run with the concrete crews and building erectors?

They've got a contact? we are actually aiming to get some builds this November

Credit to the workers for carrying everything! usually I see machinery being used theses guys are bad ass lol

Love how your shop turned out! Did you ever get the garage door opener for it? If you did what kind did you go with and did you have to change the doors or were the original doors good enough? Absolutely love the 55 Chevy! I first took notice to a 57 gmc 9300 I believe that's the Canadian version on a Show we watch. Been looking for one since lol!

Hello I just saw your video and i have a 2003 bear tracker also the original carb was swapped out by the previous owner for an Amazon one I see the top of the carb is missing a vacuum connection I need to know where it goes to also it looks like the rear brake light was changed out for an led strip and some one cut the wires too it and I’m missing one head light need to figure out how to find the wires to the rear light as well as how to replace a head light and find that missing vacuum tube any help is appreciated

You skipped over the part where you installed the metal roofing after spending an inordinate amount of time talking about fascia boards. Why? 👎🏻

Thank you for doing this video. It is exactly what I needed to see for this mower. Helped a lot to see it in use and your take on it. ☝

I have a new S130 and love the turning radius and usability. I had a D160 and this handles much better.

Can't seem to wake up I could go back to sleep in 3 min if I closed my eyes and relaxed.

This comment is late, however I did buy the S130 two years ago. Put on a mulching system rather than discharge, changed the oil system to a regular oil filter and oil drain, installed a fuel shut-off between filter and pump, upgraded to bearings in front wheels and, installed the poor-man power steering needle bearings. This machine does a great job and the upgrades were all things John Deere should have done in the first place. Nice video.

Approx how much was garage build plus slab? 30k

Hacks

Just watched this(5-3-24) and it was very informative, thanks !!

I've been looking for an air filter for mine but can't find it, where do you get yours from or the part number and what is the part number for the oil filter please????

Hmmm. I'll be moving to SC soon myself, with plans for a metal garage. I hope I don't end up with the same problems you did. I wouldn't ask you to trash the folks you dealt with, but have you learned about other companies that you COULD recommend? Thanks.

Season it first. That way whatever metal warps goes ahead and warps...that way you only have to seal it up once.

I just built a galvanized metal shop and was looking to run electric to it. If you don't mind me asking, how much did all the material cost wiring , breaker box , etc ?

I did not understand why garage door opener outlet did not require GFI protection and the light outlets did. The light outlets are even higher and out of reach or not readily accessible.

Just restored my 2002 Bear tracker, i wish someone would make a modern version of this small nimble machine. Great 4 wheeler to ride. Front shocks instead of struts. Solid rear axles fine but like Suzuki does dual shocks rear axle would be great instead of just a single shock. I took a blow torch to my plastics to restore them then I greased them up with a product called SC1 to bring the shine back and they look fantastic. Just need to get my decal stickers off of eBay. I also painted my frame and racks with farm enamel paint which is like the second best thing to actually powder coating them

How tall was the side wall?

When you have contractors do the work, they will make mistakes and some won’t tell you. They work fast and long hours so imperfections will be there. I plan to do the work myself because measure twice, cut once is a very important rule.

Hope its not he company named after a bear..ive been talking with them..i ended up canceling because they couldnt seem to understand what sides i wanted access doors.

Like ur building tho.did u go with q2 ft or 14 ft wall height?..what was the upcharge for the bubble insulation/siding?

Perhaps she might decide to document her journey thru this? Would help alot of people going thru the same thing. Just a thought. Prayers for your family. 🌹🙏

I’ve seen a comment on Amazon saying it’s toxic and contains led, I’m wondering if it’s true ?

5:52 those bits are awesome. I used to sell them when I worked at Hilti.

How did you cut the metal roof sheets?

Please shows a video of the man cave and bounce space.

Those trees are crepe myrtles

Awesome setup

What company manufactured your building?

for a 26X40 garage, what are the demensions of the foundation? Length and width.

Nice machine and good video not to mention great price for the 4 wheeler!