- 14
- 23 478
GreasyTimbers
Приєднався 10 вер 2020
Welcome to GreasyTimbers where anything wood from forestry to building toys meets automotive and machinery repair.
This channel is a mix of experience videos where I show what I have done as well as how to's that include tips and tricks.
Main areas of focus are: Milling, Woodworking and wrenching on anything with a motor (Gas and Electric)
This channel is a mix of experience videos where I show what I have done as well as how to's that include tips and tricks.
Main areas of focus are: Milling, Woodworking and wrenching on anything with a motor (Gas and Electric)
Brake Caliper Slide Pin Boot Replacement
Walkthrough of how to replace the caliper slide pin boots on a 2005 GMC Sierra. The procedure is generally the same for most calipers that use slide pins
Переглядів: 284
Відео
Door Hinge Pin Removal on 99-06 Silverado Sierra Tahoe etc
Переглядів 829 місяців тому
Skip the hammer and chisel, punch etc and use a simple nut and bolt to remove a hinge pin. This removal was performed on the 3rd door of a 2005 Sierra but the same process applies for any other door on this vehicle or similar vehicles from 1999 to 2006. This may also apply to other vehicles that use a similar pin and hinge design
Snowmobile Seat Belt Tie-Down Strap
Переглядів 859 місяців тому
Take an ordinary seat belt and turn it into the perfect sled tie-down strap While most of the ones I have used to date have come from retired vehicles I picked up this belt from Amazon at a reasonable price. Here is a link if you want to check it out on Amazon www.amazon.ca/dp/B0CDC88HLB
Tub Surround Fail - Can I Fix It?
Переглядів 298Рік тому
Brand new tub surround ruined due to a bad measurement, and to make maters worse I measured it 3 times to avoid this disaster. This video will walk you through how I fixed a misplaced tub spout hole on a brand new tub surround. Buying a replacement panel at the time was not an option, it may be now but when this was done there was a massive global supply chain shortage of everything from toilet...
HM130MAX Making 2x8's
Переглядів 1233 роки тому
This is the first log on the mill after moving it out of the shop from it's initial build location. Even this location is temporary and the rail extensions are missing. Leveled with a laser level and the first cuts were dead straight. HM130MAX from Woodland Mills woodlandmills.com/
Maple Syrup 2021 Summary
Переглядів 273 роки тому
A bit of an after thought to put together a video of my maple syrup experience this year. Much of the boiling and finishing was done late at night after my day job so videoing the progress wasn't top of mind. 245L of sap collected this year from 9 taps. Learned a ton this year and looking forward to making some improvements for next year The trees I am tapping are mixture of maple trees but unf...
Woodland Mills HM130 MAX First Cut
Переглядів 5263 роки тому
My mill is finally together and I couldn't wait to try it out. It's sitting on a wooden 6x6 frame that I can drag outside but it was late at night and I wanted to see what it would do. Grabbed a small test log and cut it in my shop.
Mini Kiln Ep4 First Load Done
Переглядів 333 роки тому
First bath of wood is dry and it's time to open it up and tell you a bit about the process and talk about a mistake I made.
Mini Kiln Ep 3 4 Weeks
Переглядів 343 роки тому
We test the moisture content of several pieces of wood inside the kiln to determine if we can move to the high heat phase to kill off any bugs in the wood
Wheel Barrow Flat Free Bearing Replacement and Retrofit
Переглядів 22 тис.3 роки тому
Making a Wheel Barrow assembly made for a 3/4" axle work with a 5/8 axle and making it an upgrade at a very low cost. New wheel assembly hub required spacers so we made some from an old gazebo. Links to products used 4.80x4.00-8 Flat Free Wheel Assembly for 3/4" shafts www.princessauto.com/en/detail/4-80-x-4-00-8-flat-free-wheelbarrow-wheel-assembly/A-p8399230e 6202-16-2RS Bearing www.princessa...
Mini Kiln Ep 2 - (4 days in)
Переглядів 184 роки тому
Check point 4 days into running the new wood kiln. Dehumidifier troubles
Mini Kiln First 12hrs of run time
Переглядів 584 роки тому
First observations after running my temporary mini wood kiln for the first time
Lighting and Burning a Swedish Torch
Переглядів 1824 роки тому
Information about the Swedish Torch (aka Canadian Candle), uses, how to light and expected burn time
LeakingATVCarbDiagnosing
Переглядів 104 роки тому
Chinese 110 ATV with a carburetor that wont stop leaking out the overflow and once that's fixed won't stay running due to lack of air fuel mixture adjustment
I wish you had explained how to remove the bearing. I bought a small wheel at Harbor Freight. It comes with the bearings I need, but I can't get the old bearings out. I tried putting a steel rod in from the other side and hammering it out, but it won't budge.
I've never had one that gave me much trouble to get off. You can try putting some penetrating oil around the bearing and let it sit overnight. Another option is to heat the bearing up and then toss some water on it to rapidly cool it. do that a few times and it may break the bond. Typically I do exactly what you have described just shove a rod in from the other end and give it a few hits.
Waste of time
didn't show how to REMOVE the old bearing
Sweet...
The reason i am watching the video is to learn how to remove the bushing and that was not shown on the video
What will usually work is to take a rod from the opposite side and a hammer and pound it out
Thanks
Useful and to the point. The perfect instructional video!
U skipped the most important part, so now I have to find another video
Put a screw driver on 1 side and knock it out the other bearing.
So how did you take it out? Was hoping to see how you popped it out.
If you are referring to taking out the old bearing since I didn't care about the bearings I was taking out I used the axle pushed it through one bearing and when it touched the other bearing on the edge i gave the axle a wack with the hammer and out the bearing came. Same thing for the other side just didn't need to thread it through a bearing as that bearing was already removed
Thanks a lot sir
Drat, I watched to specifically see how you got the old bearings off.
I pushed a rod from the other side through the center of the other axel and pounded the old bearings out. They were not in there very tight at all and since I didn't want those cheap bearings I really didn't care if I destroyed them. Alternatively on some I have done I have been able to take a flat head scredriver and pound up on the lip of the bearing to remove them.
Thanks for the video, working on a mini bike, and can use the bearing replacement idea, improving some cheap utility wheels, thanks for posting.
I did that a few years ago. But those spacers rubbed the bearing and destroyed them. Then the hub moved side to side, then the metal flange broke away from the hub of the wheel.
I was just going to mention to put a washer between the spacer and bearings but I'm 2 yr's to late.
I cant figure out why some of my bearings feel rough after i put them in but some dont literally 3 out of 6 feel rough the others feel perfect all are brand new
You forgot to grease your new bearings. Most cheap bearing come with little to no grease.
I didn't want to break the seal to add more grease for the amount this is going to be used I don't think I'll ever see that bearing fail.
@@greasytimbers9978 They make grease needle or pull one side up to add grease.
Not it's hard to find a 3/4". Almost all replacements come with 5/8".
0:52 I will setup your blog and setup it to earn money w h a t s a p p +7 9 6 7 1 5 7 0 5 8 1