Відео

Maintenance mode ! Well I’m guessing it won’t go on the highways with that mode ?

Is there a way to put a Toyota hybrid into EV only mode when it doesn't have an EV button? I want to move from the driveway to the street without starting the engine.

Dam thats alot of comands lol

tks

How much does it cost to fix that crank?

Where will you get the part to replace it

Car call needs a transmission solenoid switch

Is there a way to reset the ECM with out a scanner tool after replacing injectors? I’m getting a crank no start

2014 chrysler town and country van has same code. Same 3.6 pentastar engine too, saw another video that said to check fuse, (yellow 20 amp) interesting code.

thanks

car turned out to be an easy fix the hard part is making a good quality video like this during a work day with all the time involved, including the editing wishing you well with your channel

No help! It says no heat… you just showed how to take off the actuators. What position does the gears need to be in? Is it the top or bottom that does the heat?

Salam where are you from i have an error U0142 toyota raize any help

You are either high or extremely incompetent.

tks

Ah, shit! 😂 $1800 for a cat now. Do any of those catalytic converter cleaners that you add to fuel systems work? Getting the “lean post cat bank 1” and “o2 sensor stuck rich bank 1” codes on my X5 XDrive50i. Already replaced all o2 sensors as well.

In this case, was the high line pressure above the requested level, without control?

I had those 2 codes at the top on mine. Had those changed and now it says pending. My vehicle shakes when im in traffic and have to slow down or have my foot on brakes.

Doesn’t make any sense as the “service center” should’ve tested with their own cable and thus would’ve been discovered the root cause. Incompetence or greed from the service center?

Can I send u a picture of my mobile charger to see if its good? There seems to be some residue on it but it charges fine for now

wow tks

How many fuse for charging system

Have the same dtc, I changed oil filter plastic cap, and this valve (bought KNAUF) Issue remained. Any thoughts?

So do you change the rail sensor?

good work

What could be the other causes for that code

Thanks for the info. Question where did you get those test leads? Do you have a link I can look those up?

Would you have a link for the low pressure pump, thanks in advance! Great video!

Where are u located

Excellent video, very detailed and well-paced, explaining everything in detail. Good job!

HI!, Could you share the good one signal chart? I have the same problem on Buick Verano 2012. Thanks

Hi I have 07 5.7l hemi with exact same codes P1414, P1417 and exact in cylinder waveforms on cyl4 and 7. What did you find inside? What was the fix finally?

Mechanic at Infiniti here. This is the worst thing to ever happen to me

That fuse was blown on my car. I replaced it, and everything came back on!!!

Hi Waqas, Where do you located at? Can you please fix mine? Thank you 🙏

.... Hydrolocked water does that break the shaft?

GREAT VIDEO... THANKS

Hello, thanks for the video. May I ask which diagnostic scanner are you using? Thanks

After replacing the battery did you reprogram the car.

Do I need to unplug the battery before tightening the ground ??

U helped a lot I just fixed the same issue with my es330

which one is pin 1?

Hi.i hope you will see this..I have a Honda civic 2013 and couple of weeks back my climate control panel went out of power when I tried to adjust my power mirrors..the fan and the ac compressor is not working..I checked the fuses with a fuse checker and they look fine..what could it be?

Do you know how to remove the C pillar?

Inlet camshafts have 5 degree variance at idle?

MY 2013 EQUINOX 2.4 FAILS WHEN REGULATOR COMMAND GOES FROM 45PSI TO 17 OR LESS

Bought a used 2018 Camry with 60k miles. I do a lot of city driving with it. At about 95k miles I get this same problem with ICS and checkengine with o2 sensor code. I changed o2 sensor and everything cleared. Cars been good until a few months back. It's at 160k miles now. This time no checkengine light and no codes on the scan tool, but dashboard will randomly start showing ICS Malfunction along with Radar Cruise Malfunction, Blind-Spot Monitor Malfunction, Headlight System Malfunction, and Pre-Collision System Malfunction. Not sure what triggers it, as I'm driving the same as always. These warnings turn on probably 30% of the time i'm driving the car and they all come on at the same time. Car drives like new, no weird noises or anything. Been having this problem since about 150k miles on the odometer, it's at 160k miles now. I notice headlights will still work if i turn them on when these warning lights are flashing on the dashboard, but they will delay by 5 seconds or so to turn on. Blind-Spot Monitor and Radar Cruise stops working completely while the warnings are flashing, but otherwise will work perfectly when the warnings go off. My guess is it's probably a bad ground wire or a bad relay? Maybe I should change the same o2 sensor out again? This time I don't have any codes on my scan tool to go off of unfortunately.

Horrible audio quality. You have that air ratchet going crazy in the background.

Where r are you located. My pump just failed

Great video Thanks for share