Відео

The one is getting fuel from the separated tank to the main tank and the other supply the engine with fuel. This is the reason we are using this "special" fuel pump to AWD VAG engines. .

No, I am sorry. It is compatible only with the new version of Gauge.

Είχε 7 διαφορετικά χρώματα τοτε. "Είχε" γιατί το σταμάτησε η AEM.

No, I am sorry. The most affordable solution to replay a run would be the Innovate LM-2 solution. www.racedom.com/en/lm-2-basic-single-channel-wideband-3837

This kit includes the needed controller that will give the information to the standalone ECU you mention.

@@Racedom Thank you for your answer

@@Racedom One more question: Can you name a reason why should I buy this setup over the AEM one?

@@stefanczartoryski9085 That's a good question to make a new video! Let's say that the Innovate can connect with other innovate gauges and all together to capture analyze easily the sensors data, and the AEM is the "plug and play" king. You install it, it works. Your question has been captured for future video. Thank you!!!

Well BOV and Wastegates are two different things, each have their own function. BOV releases built up pressure . Wastegates sustains boost pressure at what you have the car setup for. But in most cases, Wastegate is mandatory.

Unfortunately there is not an official answer to this. As Turbosmart states "One-click, either way, is relative to your engine and your turbo. The more efficient it is, the fewer clicks you need to achieve more boost. However, as boost rises, efficiency decreases. This means you’ll need to work harder (more clicks) for more boosts at higher boost levels."

Yes, but you will need an MSD ignition box also.

Have you tried them? Did you measure both resistance and you found them the same ? We are open to send us a stock ignition coil and make a video showing the difference!

Noted. We have just add it to do list. Thank you.

Это видео распаковки, но это отличная идея для будущего видео!

No, unfortunately you cannot.

@@Racedom dang, but thanks for responding

@@KevinSmith-xt8xr Always!

This two holes are for the device to depressurize. By tightening the valve of the Boost-Tee it should stop depressurization. If it continues to leak after you tighten it, you probably need to replace it.

Not when its tight all the way. No leak. But when opening it up for more boost , cant boost more than my wastegate spring. Was wondering if it could be bad mbc since it doesn’t change anything. Thanks for the reply!

Would you like to to create a video testing several ignition coils ?

This is a an unboxing video not an installation. If you still want a better explanation and installation let us know and we will try to make a new video about that.

The ignition coil after time will loose its power if it is not installed in the correct position.

​@@Racedomcould that possibly be a reason for crank no start? Carb has fuel.. I just replaced the rotor wires and cap...and spark plugs

​@@RacedomDo you feel the blaster SS to be much different than the 3? Besides able to be placed in any position?

@@ari1234. NO, more or less has the same power. The position that can be placed is a true difference.

@@ari1234. I am sorry but this is not possible to be told here. You need the mechanical to take a look

This depend on the power supply of the ignition coil. If the engine uses the old fashion single point system, then yes, it is mandatory to use ballast resistor.

@@Racedom I have the billet 8361 distributor 6al and blaster 3

@@ari1234. Do NOT use the ballast resistor.

No, I am sorry.

Sale en amazon y en ebay, estoy a punto de comprarlo. www.amazon.com/dp/B01BI2PQNY/?coliid=I3AWOY8G5AOIMD&colid=30OPOGFZ0WKM5&psc=1&ref_=list_c_wl_lv_ov_lig_dp_it

If the shape if the existing ignition coil is the same , then yes you can use it.

I think it wont. We haven't test it on this vehicle. This gauge works with vehicles that has enabled the CAN bus communication on the OBDII connector. This is mandatory for all vehicles made after the year 2004. Before that year it was not sure that the vehicle has this communication protocol.

@@Racedom what wouldn’t work some of the functions of the gauge or the entire gauge won’t power up .. I’m looking for a gusher that shows me ethanol content

Yes, it will.

What you would expect ? If oyu have any questions we are here to hep you.

It's an unboxing video,its not technical. But if you have a technical question let us know.

@@Racedom ok thank you

The power is not a different part. The ignition coil is one piece.. Hope this would help.

No. This device has front and back, up and down. It can be mounted only one way.

No. It is a "normal close circuit". It needs 12v to "open" the line and let the liquid pass through. .

@Racedom I ended putting a toggle switch in it. I thought it reacted with the pump

@@XpolrerST There is an output cable of the AEM methanol controller for this.

Does it need a controller to work or can you wire it so it comes on at the same time the pump is activated?

@@Darren-vw8ov Yes,it needs a controller.

Can you please give us the engine code and details ? We also need to know the ignition coil driver. Would it be a points, or an electronic ignition driver?

If you are going to install it on a AWD, no it is not possible. In any other case you will need to do a small modification on the top of fuel pump holder. Easy

You can buy it on our website www.racedom.com. ua-cam.com/users/redirect?event=video_description&redir_token=QUFFLUhqa2NUNmJ2ckVWWWxxemVZcVdjUlk2YUUzMFVXZ3xBQ3Jtc0trc3lwblpWWG9DcXFMZGJuRTkwTmJIWmpMTXZjYTNIMC1iTmkwMVI3QmF1YlV4UHNfSEZ3bFpsR25MOUZSZGstN2g5RHp1djBmRHdTbE1ORHgxRXRPRUd4dFRzNnZfWWgwVzlSNWFzSmwycEc1bFpkQQ&q=https%3A%2F%2Fwww.racedom.com%2Fen%2Fdefi-advance-cr-control-unit-for-gauges-1&v=rlB4TYR1Un8

This depends on the vehicles. More Info you can find on the video we had added on the product page of the O2 sensor we are selling. Please take a look on the following link www.racedom.com/en/innovate-wideband-o2-sensor-bosch-lsu4-9

It is a 52mm and yes it can show PSI.

Yes, it will.

I wont be connected with your vehicle. The main communication protocol this gauge uses is the CAN bus. This is not available on 2000' Honda.

The difference is not only the color but it is also on the inlet ports. The 13101 has ORB-10 inlet ports and the 13109 has ORB-06 inlet ports.

Yes it is compatible. Most models after 2008 are compatible. There is also a guide in AEM's Website if you want to double check.

These type 1 winglets are discontinued, The new winglets type 2 are supposed to fit on a 2014 Panigale. Gripone made sure to fit most of the bikes. Unfortunately there are no pictures. So you need to confirm with Gripone before proceeding with any purchases.