Відео

What are the dimensions?

Mine only came with one rubber piece, these videos show two.

Do they make an offset version so it’s setting over the t top?

Where can I buy the aluminum bracket the same to mount some pods on my T top? Thanks 🙏🏻

I need this

I am wondering if the top portion of the t-top can fold back towards the motor, I ? need it to fold backwards so I can fit it into my garage. Is this possible

awesome now how do i put it together?

Are you able to put rods in the center console side rod holders or does it get in the way? Thanks

No purpose for the loop knot, instructed us to make a loop knot, but doesn’t show where it comes into play. Probably because it doesn’t.

NEVER put 3M 5200 adhesive on the boat if its not under water. Use 4200 instead. You will be glad when you have to remove it.

this is the correct way to do it dont listen to people telling you bullshit that you have to cut holes in your floor to install plates its false

So how about a video showing the 2 fold part?

Thanks for making this video and for the printed instructions.

Does this work for a 2inch frame tube?

This video is completely wrong for my Fishmaster Pro T-top, on mine there are 4 vertical supports with four joints takes 4-Knobs. On the canvas top there are 4 joints takes 4-knobs. You cannot put two knobs in the canvas top joints two knobs will not screw in without jamming the knobs together, there's not enough room to screw them in side by side!

Are you the idiot that thinks space isnt real?

I have a fishmaster rod but dont know what type how do I find out?

HOW ABOUT A CLEAR VIEW OF THE BAG AND TIPS ON ASSEMBLY. MINE ARRIVED WITH NO INSTRUCTIONS OR PHOTO

I just installed mine. The frame does not perfectly align. For example, the top does not simply lay into the cradle holds. You can adjust it this way, or that wya, it just doesn’t align. The engineering is off and will have to be screwed in place by pulling them down from being in a slightly cockeyed into tight position. This puts stress on the frame on the bottom and top, while I hope it will hold. Sincerely, this could be more precision engineered for the price. Nice looking T-Top, however, this not a butter the bread job because of some the misalignments and the adjustments you will have do for the lower to force match with the higher. I didn’t appreciate these manufacturing surprises since you expect things to fit perfectly. We will see . . .

Not a very good DIY video at all.

Thicc

Tore on me second day on the water.

Greetings good morning, where can I get the base of that antenna where it has that security light. thank you I await your answer

Greetings good morning, where can I get the base of that antenna where it has that security light. thank you I await your answer

Installing deck screws in the deck is NOT the right way to do it. There should be a backing plate installed under the floor for the screws to connect to. T-Tops should be through-bolted to the deck, not simply screwing them into the deck. That won't hold for years, but only months. That setup won't be strong enough, and you will notice that those screws will start to fail after repeated use in rough seas.

$$$$$??????

This people never return any communication by email or phone call they suck

WHAT THE ACTUAL FUCK IS THE LOOP KNOT FOR G

That was pretty useless...only half a bracket?

What a terrible job, at 1:31 you can see the wire is all chafed and nicked from fishing it through the unnecessary amount of holes drilled everywhere. Give it some years worth of salt spray and the whole length of cable will rot. Needless to say it seems like cheap bare copper wire was used, not marine, tinned wire.

What is the material?

Great idea to mount rod holders on lower sides of console below these grommets to facilitate storing extra long surf rods used as outriggers or a safe way to store a sabiki rod since a loaded sabiki rod stores with a weight at the tip and is too flexible to safely store in a traditional rod holder.

Please upload a video of installing these grommets. Like melting the proper holes or cutting the holes etc.. This looks to be a great product idea but they are entirely too expensive. Maybe the outer rings need to be stainless.

How fun was that trying to fish that wire through those small holes?

Should make these for the Pro T-Top

Looks good let's go fishing

Bad design, welds are ugly and the seat won’t flip up more that 4 inches. For the money you would expect something nicer. Why even hung the seat if won’t open?

My experience with the quick release knobs taught me to use an allen wrench to snug them up anyway. They will back out with road or boating vibrations. These are still a quality made piece of gear, and I use them but don't really need them since I must use a hex wrench anyway. Your experience may differ from mine.

What about the wiring?

This box should have a clamp system most people don’t want to drill the tubing

So, how do you get a rod in the console rod holder with no hole in the T Top canvas???

Just ordered one. Thank you for sharing!

I just purchased this and love it!

*This rod holder is strong>>>**allabout.wiki/e39z** but lightweight. It's good for keeping your fishing rods steady and securely. No need to stand holding a fishing pole if fish are slow. This is definitely a great item and it makes a great gift.*

?

You also show on your website that you offer it in white and I ordered one and I hope it’s white and not white and black because you don’t show a simple pic on the all white one

Why don’t you show how to put together the back part you also sell

Wish on these t-top videos they would explain where to install it on the deck, don’t ya have to make sure it’s tied into the stringer?

you started off showing the middle loop knot then skip to showing you threading the top 5 or 6 loops later. please show the very begining of starting to start the rope around the pipe for the first time

Radio box, rod holders or antenna mount available for the “pro series”?