Відео

Mines keeps stalling Has New Fuel Pump New Fuel Filter New Mass Air New Fuel Pressure New Plugs New Idle air sensor and still Stalls if give it Gas it stays on and sometimes it runs and fine then randomly shuts off at Stops. Always starts back up I’m at a loss

Pioneer Ohio!, I used to live in Montpelier long time ago. When I travel thru NW Ohio, Napoleon, Defiance for Telco I see many 4228 or 4221 antennas combined with a VHF yagi. Some are on American towers and some on tilting towers. Not sure who made those tilting towers that piggyback each other. I always thought the same company installed many of those since they were so similar. OTA TV is making a comeback. OTA plus streaming is the way to go. Minimal expense compared to CATV or Sat TV rates. You look very comfortable on that tower. I used to climb telco poles but my knees can't take it anymore.

This was 100% the solution to my problem. Thank you

YOU SIR, ARE A SUPER STUDD!!!!!!!!!

did this happen after it had run? Mine does the same thing after warmed up.

Mine Studdard and died but cranked back no problem

You really helped me out thank you

Why a TV tower I saw a satellite dish?

Hell yeah

Old amerite tower repainted..rust inside...put up very many...sorry, but junk.

I have the same issue with my 99 and it will run if I unplug the MAF, but dies if you give it throttle. Any ideas?

The sections seemed very light to lift without a pole. Is the tower attached to the House on top, it seems if not the wind could bend it.

worked perfectly, ty

Question: When you pulled the bad sensor and ran it, did it run like normal or did it rev and act abnormal?

Who builds a tower in front of their windows?

It would’ve been MUCH easier and cheaper to either use a 10’ mast pipe with an eve stand-off wall-mount or a 5’ mast pipe with roof-ridge tripod.

Thanks for posting. Mine was doing the same thing. Pulled the connection and it ran just fine. Put the new sensor in and seems good so far

Hell noooo lol the trafficwind

I built mine on the ground with a hing plate. Push a button and it stands up or lowers to the ground. Much easier to work with your feet on the ground!

$100 that's outrageous guess I ain't fixing mine

what a waste of tower for a stupid little tv antenna. Now if it were a 10,15 20 meter beam thats something different !

Very well done you did this like a ACE thanks for the video.

Now that is a high antenna tower

Any specific detail about the technique used with the belt thing hooked to the mast so you can work with your both hands? Looks stupid but a 2 minute crash Course on that specific thing would set me ready to climb mine with ease. What belt did you use? Where can I purchase one line that?

All that work for a baby antenna!

Proper cable dog knows his job 👍

If this is what the customer wants. He got a great setup. For the rest of us a heavy duty tripod and mast would knock about $600 off the quote. But I know some people are not willing to risk roof leaks with a tripod. I would want a tower if I was in a lightning prone area like Florida.

When in doubt, hit it with vice grips.

At first I thought this video was very old maybe from back in the 80s but then I seen the Dish Network satellite receiver

Like a BOSS 🤣😂

My neighbors would love me if I put up one of those!Not sure if the insurance would cover if and when struct by lightning!

40 feet tower for a little tv antenna a db4 would have more channels

Have never seen that type of section any were there was a very old manufacturerd sections of mini tower don't know the brand but probably long out of business. that is similar with the all tube construction but was very similar to 25G in spacing on the cross pieces. That one looks home built NOBODY else has been able to know of it.

This is so cool. I didnt even know tall towers like this existed gor home use. How much does a tower install like that cost, roughly?

are You really have to install this in the middle of windows ?

That tower isnt steel its aluminum

What brand of tower is this I have one just like this but need to find another section

You really don't need much of a base, for an install like this one. I have almost the same exact setup, I drove in (3) - 6 foot x 1" diameter pipes slid the tower over the pipes, put a round disk blade down over the pipes, (so it wouldn't sink into the ground) and fastened it to the framing members of the house, with angle iron. It's was up 28 years, with a 5 element beam and I was up several times to make repairs , over the years. Once its fastened to the house, the pipes just keep the base sliding sideways, all the weight is downward.

Maybe that music caused the driver to fall asleep and crash.

As tall as the house peak is, just put a gable brace and 15 foot pole.

So I'm curious as Wat you did as far as securing it to the ground? I have a 60' self supporter and thought about pouring a 3'×3'×3' concrete block in the ground but the thought of even 12" anchor bolts scare me. Any ideas? My tower is a lot heavier than yours

Would it not have been better to have a 10ft mast on the roof instead of wasting a bunch of tower?

Truth and Quality. Practical and Useful Information. Light Weight Aluminum , Free Standing , Lay Over Towers , No Guy Wires , Lay Over and Install Antennas Standing on the Ground. , www.palcoelectronics.com

Wow pretty stupid, just put it on an eve mount.

How does tower anchor to ground ?

wtf

My neighbors have one in their yard

The one big defect that comes with those Towers is the nuts and bolts that come with them. They're nice and shiny when new but start rusting quickly. When I put up a TV antenna with the help of a friend, I headed over to the Hardware Store and got Stainless Steel replacement Bolts, Nuts and Washers.

Thank You..Back in the day my husband hauled pallets and the only truck that would hold up was a Ford F 150...A Beast