Відео

Good video brother

I have a wet K&N FILTER been running it for about 2years..sounds great

Best video for 2017

Your problem should be on the wiring, the section between the door hinges

Try on a dyno and see what’s the difference

I removed the electric tape

Every single bolt amd nut on every vehicle made in 20 years besides a oddball battery terminal......IS METRIC.....

Thank you bro, some a hole side swapped my car while it was parked on a city street and broke my side mirror. I was able to purchase the side mirror a very reasonable price as opposed to ford’s $1,600+ price for labor and part 500 of that money was the cost of labor. I got this thing done in less than 30 minutes because of your video. Thank you mane

Did you notice any increase in MPG?

Removes oil cap but doesn’t remove plastic cowling to make job SUPER EASY! SMH

Best video on the topic!

Thanks for sharing this I learned a lot.

❤❤❤❤❤❤

What cualcing you use

So helpful! I fixed it!!!

check your ground straps

My alternator plug was integrated to the alternator on my 92 f150 5.0 . Hope this helps someone. I thought i was weak/crazy. Cheers

Of course no passenger side replacement. What a waste of time.

The factory cold air intake has many gaps and dams to prevent water from getting sucked into the engine. The airbox has a decent sized drain hole. Its not a pure cold air intake but it will keep intake temps lower. Taking off the airbox lid is not going to change much. The filter, inlet tubes and turbo are limited in volume and temperature is very important. The intake would be a short ram air intake with the lid off. The best upgrade would be a more efficient intercooler

Mine broke, so ive ordered parts to replace it. Thabks for the video on how to replace it!

Looks like the brakes are worn out.

You are not getting your views

This is my daughter's car and hers broke. As a widow I can't tell you how invaluable these youtube videos are! Saves me hundreds of dollars.Thank you so much.

If the egr is set closed unless it gets a signal just keep the egr on just use the plug. You don't have to even use the block off plate. Save the $20.

Dont change it like this guy! Use 2 hands smh

good video man ! thank you

How long does this take start to finish ?

Can't believe he didn't douse them nasty brakes with cleaner. You have it opened up why not take a few minutes to clean them? In time they'll end up glazed over.

Great video. Only complaint is taking the clip off, could really see where you were prying it off from, but it made sense when you put it back on where it comes from. Thanks for a good video!

Dear God thank you

He said “grab your dipstick”😂😂😂

It's been proven that unless you use other mods to increase hp, a cold air intake filter does nothing for the stock turbo motor in an Escape.

what size socket is that for the hub? doing my 84 i’m gonna assume they’re the same

That's not a cold air intake, looks more like a hot air intake. Heat from the engine will get into the airbox.

Doing the same thing this week

Good video. What was your extent of paint prep? What kinda paint did you use and has it held up?

helps alot thanks for showing the voltage meter in the truck at the end!

Where is the fuel filter? Thank you so much for the excellent video!

Nice video. Have you noticed delayed engagement when going from park to drive or reverse to drive? My 2017 Expedition takes 2 to 3 seconds when I shift from park or reverse to drive. Kind of a pain in the butt, especially when going back and forth with a trailer.

How many miles on your 2016 Expedition? Have you any major problems?

They rust out. I know mine did. I had salt buried in mine.

I'm having a hard time removing the dangling thing to get to the bulbs what can i use to get it off?

Thank you! I never would have figured it out without this video. A. Stupidest wiper design ever. B. Worst instructions on the wiper blade box ever. She' all fixed now though!

Its not centered on the plastic cover. The new blade should stick out a little more than an inch. If you are able to look at the back of the plastic cover(which you should be able to), you will see exactly what I speak of

They change the OEM wiper in 2017 for the rear. If you have had a changed, his method may work on an aftermarket wiper. On some of the OEM this will break your wiper. If his method feels like you’re putting too much pressure then try this method. Lift the blade slightly off the glass grab the end of the wiper blade and pull like you’re trying to slide it out. You’ll be pulling to the right. You will hear a pop if it is an OEM blade. You can then after the pop, pried off like he shows . The OEM blade has a hook on the blade that requires you pulling it to the right to free it. You can also look this method up as a 2018 rear wiper blade installation for an escape. They should show you this method.

Were was the fuel filter at ?

Hello there 😅 no disrespect I know you should disconnect the negative cable first instead of the positive first 😮😅 just saying lol

Great video, thanks! Question: Why not LED upgrade? Faster response rate, less heat and great looking blinking action

I have LED brake light version. All 3 LED lights are out from rainwater. Anyone have luck buying a non-ford housing? Can you send the website? Why would I buy the ford housing again if it is likely to fail and need to be replaced again?