Відео

@@KPtain_RC thank you I appreciate that!

@@manuelcapelli4596 what’s specificity did you need, I am selling the whole bike after I finish a few things on it, I got a few parts

@@tanmansbikebuilds931 clutch cover

SFB Racing

@@manuelcapelli4596 unfortunately it’s the only cover I have, it never came with the stock one but ill double check and let you now

@@rls3231 I think either majority of all of the shavings got picked up by the magnet on the stator cuz the only remnants of shavings I could find I whipped off the stator, i also did an oil flush through the motor, left that stator cover off and put 3L of fresh oil threw it in hopes to remove any of the shavings

@@rls3231 old girl still fires up fist kick

@@albanramadani9029 of course I’m glad it helped!!

Am trying to get oli filter at amazon i think they dont have it

@@albanramadani9029 OIL FILTER A-5GH-13440-60-00 YAMAHA OEM On Amazon

@@tanmansbikebuilds931 thank you so much

@@albanramadani9029 of course!! Glad it could be of help

Yah you bet so there just wasn’t enough room to bring the chain over where the sprocket mounts to drop the chain down, so to remove the head you need to remove the camshaft so you can drop the chain and pull the head off, makes for a nice quick disassembly!

Oh yes I do see what you are talking about! It is caused by the chain coming off and piling up but luckily with gasket maker on my cover and it doesn’t leak oil but can be a big issue if so, unfortunately in worst case you would need to replace the whole left case

@@mateusattie3625 if you want a bit of a power boost to lift heavier bbs, all you need in this gun is a non ported cylinder! That is all and they are super cheap

@@StickCannon tbh I think they are just all like that I’ve gone over the whole bike and made sure everything was tight and still vibrates quite a bit

@@tanmansbikebuilds931 I put 8 washers on the 4 engine mount screws and grip puppies on the handlebars it's way better now

@@d.l.horton2093 thank you I appreciate that!

@@RamonGamez-b7y I can sure try! What seems to be the issue

@@StickCannon no more then a couple hours, I did 3 heat cycles of just idle then putted it around then let her cool down then opened ot up a bit then cool again then I just let her eat after that and yah crazy results!

@@BondocJomar that is a good question! Tbh I’m not even sure

I have a 98 and it started doing that I tighten it up and it stopped

I ended up needing to replace the timing chain and the guides, as the one that was in there was stretched about 3-4mm it hung lower then the new one, I also had to replace the tensioner aswell because once I backed the 10mm off the tensioner and put my screw driver in there it was seized up and wouldn’t budge, after I put the new one in it snapped tight as soon as I released the tensioner, but definitely at that time the chain was way too loose

Gotta love the sound of a fresh 2 stroke eh!

The carbs where so gummed up from sitting for 6 years, the fact that is even started was a miracle, go look at one of my more recent videos on the sled where I have them ultrasonically cleaned! The results are night and day!

The carbides on the skis catch on the ramp I was using stopped me dead in my tracks, 100% I needed the plywood or a proper snowmobile ramp, not the atv ramp I only had at the time

Very good old unit she is! Still ripping today after the new top end

@@tanmansbikebuilds931 i have a 96 kodiak 400, it came with a spare set of plastics because the originals were a mess.. so mine looks like yours only green and with a rack on the front, had to rebuild the top end too. Runs amazing!!!

This here will give you a 44mm piston giving it 66cc big bore www.ebay.ca/itm/184036025151?mkcid=16&mkevt=1&mkrid=711-127632-2357-0&ssspo=ecfva_EBTLu&sssrc=4429486&ssuid=&var=&widget_ver=artemis&media=COPY

@@tanmansbikebuilds931 how much faster does it go

Only because it has a turbo, Improved Air-Fuel Ratio! A custom tune can adjust the engine's air-fuel ratio to take advantage of more efficient combustion and potentially further boosting horsepower and fuel economy

If not you risk to much air flow but not enough fuel causing it to not run properly or at its most optimal

@@tanmansbikebuilds931 is there a good tune i could buy to go with the cold air intake.

same

It will be sticking out if you unscrew flash hider. But problem is where 420 has its orings.

100% it is the only one I have seen in blue!

No unfortunately it will gear down a bit making it more torquie but less speed, look at getting the 2 speed and upgrade your electronics! That is your best bet

@@tanmansbikebuilds931 Thank you bro! Unfortunately I just saw this comment of yours. This means that I already purchased the 370 motor set and after installing it, I noticed the car slowed down and returned it to the original motor. There were more holes in my car. LOLOL

Of course so unfortunately that motor and transmission set up is quite a bit more beefy but it is geared down a bit for more torque for climbing and haling threw mud without cutting out where it does lack in top speed

Tbh from my understanding they are still manufactured in Japan and built and sold to mass producers coming out of United States

Turned out my reciver fried and was malfunctioning after I got it soaked in water! Got a water proof reciver and new radio and the throttle calibration worked first try! I did get the programming card and got all 15 settings saved how I want! Go look at my recent short it crawls amazing now

Thank you I’m glad you enjoyed

Thanks for the heads up

Wasn’t in control of that truck what so ever, just took a video.

Was not my crawler…. Just did a review on a buddy, go look at my crawlers the purple scout ii and my trx4 sport that I built a Hilux body for, that is how I run my rcs

TRX4 Yoda Crawling in the Okanagan! #fyp #rc #crawler #hilux ua-cam.com/users/shortsCBA9s_Tx67w?feature=share

100% you are right..

It should have come with one, if not it is a 2mm Allen wrench

At the time i did this I didn’t know the knowledge I do now, I do plan on re trying the tight bore but this time r hop the barrel and then see the results

And what results have you got? ​@@tanmansbikebuilds931

Yah it would have been around $575 usd at the time

100%!

Turned out to be an awesome day

m.traxxas.com