Відео

There is a fiberglass boat patch kit on market which works much better than putty for patching holes and is more durable. Using both, you need to seal the hole from other side with some tape for best results, and like this the product will not fall out from the hole.

Awesome!!

GO MIKE!

what to put on the items to stop from rusting after clean, I mean for long term rust prevention?

I use a cheesecloth and strain the ultrasonic solution into a container. Great idea to mark the level to add water later.

Use a steamer.

running a foam business sucks, you can't measure foam in "Rs" per inch, one inch is better than 10 in of any batt product,

Did you even read the instructions to your ultrasonic cleaner? Parts should never touch the bottom of the tank. This will drastically suppress the creation of vapor bubbles that do the cleaning.

Very good ramp but please cut the music.

That's a cross cut btw not a rip :)

What's with the sign that says persons only in the goose neck end....? It's also the end with the different looking flooring the center.

I love this home

Great video, I think if you run a 3rd test with heated evaporust solution instead of the ultrasonic cleaner your result would be pretty simular, remember chemistry 101 for every ten degrees Celsius increase your chemical reaction will increase by 100%. The one thing about the ultrasonic cleaner is that it will move the reactant material away from the iron object making it work better. When you use evaporust without an ultrasonic cleaner you must remove the reactant material with a steel brush to make it work faster.

What would you say was the approximate cost for the complete project?

The cabinet looks great with high quality materials. I am curious about calling the coroner at 3:18 into the video.❤

What else would you use an off & on switch for no explanation needed.

thank you so much for this video

This cheaper but takes longer De-rust 100ml dist water 5gm EDTA citric acid to buffer to 6.5 Buncha drops of soap It did loosen some set screws that I'd thought I was going to need to drill. I think the soak with or without, ultrasonic, would do best in joints and threads. I used the homemade stuff in the ultrasonic. I'd only expect the VapoRust to work better.

I've been thinking that the ultrasonic would likely be good for getting into threads and the joints is jointed tools.

Try Suspending heavy items from a frame NOT FIXED TO THE UNIT so there is no contact with the sides or bottom of the cleaner or tank, contact with the tank supresses the ultrasonics and eventually destroy the unit, Heating helps heaps, You can even use Gasoline or many solvent's but be warned NEVER exceed !#"60centigrade"#! best to keep it around 50-55c or below the flash point of the solvents in a well ventilated area out side in the open is best,and stay away from fumes some could be extremely unhealthy, I NEVER use the baskets small items go in to plastic Peanut butter jars with degreser or what ever and just float the jars 90% submerged in plain water in the tank works fine and saves lots of otherwise wasted cleaning solvents. There re plenty of other tips doos and dont's on line, Cant wait for Laser cleaners to get a lot cheaper totally unbeatable for cleaning. Best Regard's

Evapo Rust is one of the very few products that does what it says it does. It is also safe to handle and dispose of relatively easily.

A lot of filler content.

That's why nobody gets paid, Untill I get inspection done. And why I do most everything myself $0.02

Be careful, I have a container on the coast And put coating on the roof,salt water got between the coating and roof panel.. going to put a roof a foot above my roof to fix leaks and stop the heat ,do to the air flow between the 2 roofs.

This guy is a clown, stagger the joints. Union Carpenter for almost four decades.

Seems like it works, and cheaper than renting a panel lift 👍 not sure if you're planning on finishing it any, but if so it's best to stagger the end lengths so you don't have an 8'+ long butt joint; it will definitely crack.

This is what you can refer to as a worthless video...Here's a guy that didn't apply or prep for the spray foam, critiquing it...That's like a woman that never played football critiquing the play call.....Kinda reminds me of the home shows where the host scurries about with a tool belt on but never pulls out the hammer....Just my opinion

Evapo Rust is superb. Ultrasonic derusting is fantastic. TOGETHER, they are a game changer!

I can see grease goes away with heat but don't see for rust.

Do you do work in Rockledge??

Why do they only use them once?

Love it. I need one👍

From what I can see it is only a warehouse with no manufacturing, but it is their main place in Kentucky.

i did this same set up but the pvc did not melt to the black abs platic too weel and sprays out of 3 of the zones

fill tank with water then place tools in gallon freezer ziploc with couple ounces of cleaner

Thanks for your review! Can we share the link to the video on our social pages?

Not sure why everyone doesn't use 1/8 x 4" steel for this .

Nice video. Great information. I’ll be getting with you on an upcoming project.

We just bought a new construction home. The amount of shoddy work, lack of communication, and actual ghosting from companies (some under warrantee!) have baffled and aggravated me. This cannot be the new normal for business.

If you have a cordless drill, put it on slow speed and chuck the small screwdriver in it. Then screw away. Hopefully your drill has a slow speed. Could use a corded drill, but more work and awkward.

We call mom the funbuster in this house

Good stuff. Enjoy those kiddos!

Yes, yes... faster!

Thank you Whobudddy! I greatly appreciate that video.

Thanks dude! Got one to seal up in the morning!

you shouldn't be able to push a screw straight through closed cell foam that thick. looks like it's B-side rich, Not good. don't live in that box

Cool beans 🙃 I have the same cleaner you have there & I have never used it. Harbor Freight has a bigger one, just a little bigger but nicer you have inspired me to try mine one of these days

Hyperloop?

This isn't the Hyperloop, it' the Loop. Loop: paved tunnels for Tesla vehicles. Hyperloop: depressurized tunnels/pipes for high-speed maglev pods.

That's quite a wait list!