Відео

THis can also help with cross bed beam alignment!

Just installed the kit and there is a small amount of air coming out of the nozzle with the machine off. Is this normal?

What PSI do you set this to?

Great video! Just got my kit, looking forward to installing it. Would also love to install a stack light. Do you have a source for them and a video to install?

I have ordered it a month ago, but have not received it yet. Can you get back to me about the timing?

I ordered one as this seems like a nice setup, but I'm waiting to hear the status of my order?

Hello! I've tried to reach out to guys via your emails and Facebook but have not gotten any replies. I have a couple of questions for you regarding your system. Please reply so I can ask and order. :)

Hello! I've tried to reach out to guys via your emails and Facebook but have not gotten any replies. I have a couple of questions for you regarding your system. Please reply so I can ask and order. :)

Thank you for your video. I have been dealing with my laser being out of square for a while now. Your video pointed me in the right direction and YES it worked. I solve the problem of getting a square to measure rail to rail by clamping a 1-2-3 block the Y rail. That gave me the height and a good reference to use my square to straighten it out.

Mine loosened over time. Thx I’ll try this.

@4:05 HEHE... HE SAID "GRAB THE SHAFT"...

Thanks a lot for the good explanation and ideas on how to measure the bigger diagonals. Very good job!

is this kit still available? Will it work with the Rudia 6442s controller?

wut dis do?

Hello! Realy like what you made! This kit is amazing!!! Did you send to Austria? I wrote two Emails, but no answers😢 Hope you are ok?!? Thanks!!!

Manufacturers should provide better maintenance tools.

3,4 5

I have a 100W Omtech going to up grade with your system, what compressor do you recommend that quiet? You have a email? thanks

Works fine but my job is complete and turn off the laser, i still get low flow air coming out of the nozzle. This should not happen, right?

Looking for status on our order. It has been three weeks with no reponse to our emails. We received confimation but, no updates.

Are you still in business? I placed an order a little over a week ago, and have't had a response.

With most macvhines the Y belt tension is achieved by adjusting a unit on the backat each end of the gantry. If you tighten the ajustments differently this may be the real cause of the gantry being off square so be careful to adjust both belts by the same amount. The method demonstrated is exactly what you need to do, with the big sqaure and equal diagonals method. However there is one impoertant point missing from this video..... the gantry bearing blocks. Those bearing blocks are usually pre-tensioned onto the rail to ensure they are bscklash-free. If you twist the gantry then you are twisting the beaiing blpcks out of line with their free running position and this will result in premature bearing wear.. It is therefore important that your slightly loosed the end bearing blocks so that they can "float" into thier natural stress-free alignment. Dint forget to retighten them after you have squared the axes..

We placed our order. Do you have an update on lead time? Purchase was made 7/21/2023

Thank you , one of the best info videos i have seen on youtube for a while, I knew I had a problem but not sure why things were coming out not square.

Tried to contact you to see when my kits are shipping

THANK YOU!... while sometimes I feel mechanically and electronically inclined to do these things on my own, this guidance is spot on. Cheers.

You the man.

super helpfull thankyou

I installed my kit with no issues. Easy to follow instructions. Works very well on my Ruida controlled laser with lightburn as the software. Much better than my "manual" adjusting of air that was provided by the wheezing little onboard air pump. Hooked to my shop compressor, cutting and engraving results are far superior. I'm not affiliated with Artifex - but credit where it's due - it's a good bit of kit and I recommend it. Cheers from Australia.

Do you have a list of what to buy? For the pump assist? My pump will be here today

I need some troubleshooting advice. The air compressor assist kit works when the laser is not running, turns off when the laser starts. Any advice?

What diameter PU tubing is used in this kit??

I've ordered one of these kits. I've heard good things about them, here in Australia.

The upgrade says to plug a cable into the laser controller, but there is a wire in the 24v port, am I supposed to remove that?

Does anyone know how to reach this company??? I accidentally ordered the wrong upgrade kit and they do not respond to email and NO PHONE NUMBER! Please help!

I have a 1x1mtr diode laser machine with alignment issues.. and no one can tell me how to calibrate the rails.. its driving me crazy

Greatly appreciated!

Do we need to disconnect the existing air system in the machine?

How do we deal with the tubing if we dont have the 2 air assist outputs shown at 10:19?

Do you guys also sell the stack light as a plug and play kit?

I Just ordered a kit 9/4/22 Hope it come sooner than 2 to 3 weeks, but we shall see.

This is awesome!! I’ll be ordering one of these kits. I know how to wire up the solenoids directly to my board but this just makes it so much easier and convenient.

Thank you for sharing! Very useful! This should be the starting point of a proper laser calibration/alignment. Regarding the squareness between the x and y linear rails, do you think a 3d printed custom square would be accurate enough ?

Thanks SO MUCH for this tutorial. I searched high and low and could not find this information!!