Відео

What if you install the SLP flow pac duct and build a duct from the ram air hood to the box ? Now u just funneled cold air from top and bottom ??

The factory round diffuser doesn’t work with the npp mufflers kinda be like a rectangle in a circle hole.

i never had any issues with it.

Definitely the music haha.

I used a dremel but any cutoff wheel should do.

@@powerbytwitch3073 sweet I just found out about this mod and was going to do it myself thanks homie, how does she run after you made the cuts

Not an SS so it’s not a factory ram air car, opening up the air box allows a lot more air to reach the engine. The front opening on the air box of these cars is a bottle neck. The trans ams have a larger opening but that air box won’t clear the camaro hood.

@@powerbytwitch3073 ok, not an SS... i didnt get that part. you may have been better off drilling holes on the perimeter of the base below the filter vs having your intake directly ingest hot air coming off of the radiator at low speeds. thats an old trick for some older generation street bikes that had airboxes that had an internal volume that was too small for the motors they fed... just a thought

@@powerbytwitch3073 keep up the DIYs though...always good to see the younger guys tweaking on their rides. good stuff

@@petrorr possibly, they make a shrouding kit to limit whatever hot air may be ingested just never got around to buying one. Really a tube routed to the bumper would’ve probably been most effective but GM kinda limited what you can easily do without a lot of cutting and moving parts around.

The hood on the ss is not functional unless you buy a kit to extend the air box so that it seals to the hood. And even then the effects do not take place until you’re rolling hard. I did this mod on my ss and picked up a noticeable difference down low. And it sounds mean af without the silencing bellow

Sitting still I’m sure you are drawing in a lot of unnecessary heat, but once you are moving it should be minimal being that the rad is behind where the air is being drawn from. A bone stock car probably wouldn’t benefit from it much but with nitrous, a bigger tb, and more airflow mod the air box becomes a restriction. They make a shrouding kit to help with any heat but for something you can do in your garage for no money and free up some cfm I don’t se the harm in it.

This is for high rpm. Great for cammed cars. To put it in simple terms it increases the air your car can take in

Booqueefious Queefs It’s a Husky 3/8 In. Drive 12V cordless ratchet

So what do we do ? Bc I want to do mys bc for some reason it makes it hard lol .

@@dtercero1284 4 bolts at the bottom inside of diffuser and 2 T the ends.. then just pull diffuser. Its gonna be a tough go 1 by 1

@american muscle305 ok thx

Of course its needed to remove it then how will takw off the clips

sorry that I'm just getting back with you but no i didn't have it on a dyno as it would have most likely not shown any improvement without any air flow.

I cant say for certain, There appears to be the same plug in the back of the sohc heads so i would assume it could be used just the same. It might be a safe bet to contact one of the companies that make them just to be sure.

@@powerbytwitch3073 oh. Ok thanks

absolutely, glad I could be of some help.

Danilo CR I just installed them to where the valve was open all the time, so I didn’t have to do any wiring etc.

The Great Beezolini my girl ordered it from summit racing. I believe the shipping came out cheaper through them. Gm parts warehouse sells them too I believe.

Power by Twitch just ordered the diffuse and yonaka quad tips today will be uploading that soon

The Great Beezolini Sweet man, I’ll make sure to check it out. I just ordered the springs, pushrods, and retainers so I can do my cam swap hopefully it’ll be up next week.

Power by Twitch i appreciate that man you got my sub🤙🏾