Відео

Thanks helpful

Any tutorials how to remove it?

Thanks for the video. How would get it centered.

The bolts are crap ….just installed one of these , the top sheared off the bolt while tightening ! Then again everything you purchase that has supplied screws …the screws are crap .

I searched up "can I tape jack met to a wall" and it gave me this. Thank you. 🥰

Missed one screw?!

Where do you buy your pier cap molds?

Whyyyyyy!!!!!!!! Why make a 12 minute video for something that should only be two minutes

Thanks for the demo, very helpful. I'm wondering how effective it would be to fill the air bubble gaps with filled concreate?

Thank you, life saver video 😍

Installation tip. Before mounting turn the pier caps upsidedown and mark the outline of the pier using a pencil. That way is far easier to centre and postion them during mounting

Would it be a good idea to use a bit of metal or mesh in the middle for strength?

Nice job. You might try a directional mic to avoid the mouth breathing of the cameraman. Constructive criticism.

But what if someone just rips it off the wall?, better to screw to wood.

Sounds like Mike myers was videoing this.

Sick video

why the hook can move around?

But whatever you do don’t install a MasterLock one!!! 😱 They are so easy to pick.

Thank good info video

Very helpful. Thank you!

where can i find plastic mold size 31"x31"

Love the tip using the tyre for support Jack , my little tip is cut a square of plywood a few mils bigger on all 4 sides than the actual column it is to sit upon , then set it flush down on the wet surface ( may need a weight to keep it from rising ) , prise it out when concrete is set .....Now the cap will seat snuggly on top of your column .

So, you penetrated the membrane? Anyone watching this to learn how to do it at home, just know that builders can't get away with this because it compromises the bathrooms waterproofing. Any leaks under the tiles will find their way to this hole in the membrane and travel underneath the membrane to the edges of the bathroom floor. You can get stick on door stops, or fix it to the door.

Hi Jack, great video. Can you please tell me what size drill bit you used?

Why would u check the level if it’s not been drilled in you would drill it’s first fixing then level it

What size drill bit?

All the PPE at the start gives the impression of being professional then I see you working in a pair of sliders.

Thank you very helpful

research correct concrete mixtures for all applications .. this guys use of of non specific ratios of cement to aggerate to water to whatever else he has in the mix makes no sense and will most likely fail in a short period of time. Cement mixes are very specific for different uses.

Very helpful thanks

what about safe shoes?

This video was incredibly helpful and well put together. Thank you!

Great video Jack. The Master Lock that Jack installed is not supplied with masonry screws. They are regular screws. The installation instructions that come with the product actually advise the use of wall plugs (also known as rawl plugs) when mounting the product on a brick wall. BTW, NEVER use concrete screws or bolts to install Master Locks onto brick walls. Concrete screws are great for fixing things like window and door frames that don't move a lot. But they tend to come loose when put under tension with potential movement (loading unloading). Wall plugs are definitely the way to go here with one caveat ... for extra security to make it more difficult for the Master Lock to be ripped off the wall, place the wall plugs into the brick using a strong adhesive glue (eg. araldite epoxy glue or Liquid Nails for bricks). And then apply some epoxy glue into the wall plugs before fixing the screws in place. As for PPE, always use a face mask, eye protection AND ear protection when drilling into bricks. Also, when drilling holes directly into brickwork it is a good idea to use a drill that has an impact function or hammer function. Just makes the job tha little bit easier. But with patience and effort, a regular drill with a masonry drill bit will work fine for holes up to around 6mm in diameter. Let the drill bits cool down for a couple of minutes after use before handling them again. They can get pretty hot. Make sure to clean out the holes before inserting wall plugs. Personally, I prefer to drive the screws using a manual screwdriver. It takes a little longer but less chance of making a mistake. Finally, remember this sort of device will protect its contents from 99% of people. However, there will always be that 1% that will be able to break into the thing and access the contents. They are convenient but not 100% foolproof. But then again, what is? Cheers.

Promo_SM

Dang your camera man is having hard time breathing....its loud!😂😎🍻

If you want to buy the same mould I used you can use this link: Plastic Molds Fence Pier Cap Concrete amzn.to/44FU3Np

☝️ "Promo SM"

Those were concrete screws. No wall plug was needed. Much more secure then using wall plugs

I just forgot the code 😢, what can I do ?

Can u share link of same shape mould, am from india

I thought it was DIY your using a mold

Great job. But next time add sand to your mix. We used to order concrete 3:2:1 3 agg 2 sand 1 cement Keep up the good work buddy

where did you find the pvc molds?

The concrete is the easy part. You should have showed how to make the forms.

The camera man has ash ma or something he breath so hard

Thank you, have used your making pier caps and this video with great success! I was going to use mortar for bedding, but this way is much easier as I was having trouble lifting onto the mortar bed, now I can just slide the caps into place......Thanks again.

Looks great. Nice job

Good work Sir. Nice job. You may in the future add some wire before the pour to provide extra strength to the cap and prevent breakage. Good video. Cheers from Texas!!!

Great video I really enjoyed it

Good job but when your trying to get the air bubbles out don’t smack it hard instead make smaller taps with the hammer but more frequently. Most ppl tend to give it a few good wacks and Un intentionally add more bubbles