Відео

What speaker did you use? Not really clear from the video, looks like you salvaged one from a baseball cap of some kind?

how is it holding up! ?

i did the filter swap today but now my truck wont turn over just crank any solutions?? thanks in advance!

and the drain plug is vented to leak when over filled with 80 90 gear oil

ITS NOT SEALED OIL TIP IT AND THEY DUMP AND ITS 144

Install gaskets dry?

Do u have to have an timing retard box for these small superchargers??

what up fam\

Hey bubba you ok ??

You just got to scrub it a little bit before you rinse it

How do you charge the 20v battery in the 12v power system?

This is that famous name! Mr. Bubba Ayers ! That name is held in high regard among some very respectable channels! When UA-cam gave me the thumbnail I clicked right on it!

Never saw an alternator do that before. 👍👍

Hi Bubba, good to see yuh! Sorry to hear you had a misfire in the old blood pump!!

Hey Bubba good info. Good to see you back!

Great to hear from you bubba hope your well

Back in the woods I love it! Awesome job Bubba! 👍

Nice information..pretty crazy noise there..✌ Take care..

Thanks for sharing. Good to see you. Been a while. Hope all is well. Keep the content coming. Enjoy your day.

Thanks for sharing sir!!👍👍

BUBA !!!! Great to see you, hope all's well . 👍🇺🇸🫡

Hold my beer Jethro we gonna burn some rubber.

Bubba,could you please leave the information flashes up a little longer?

Hey bubba aint heard from you in ages hope you're well

Hold the sprayer down

How's it holding up I'm deisel mechanic would you recommend it

Jeepers Creepers 383 chevy B&M Blower lol

12 before top dead center its 1 degree for every 2 pounds of boost I buy quarts of 12 percent Nitro remote control car or airplane fuel put 1 pint half bottle in 32 gallons of 93 premium beats the heck out of race gas and truck wont Be detonating below 32 degrees wont hurt valve seats or any thing used for ten years about 150 octane mix 76 Blazer Race truck Daily Driver Kicks butt I am Addict of Nitro fumes for 10 Years and not in Denial lol I have shakes and nightmares if I dont have 10 bottles in my Garage Ha Ha Ha If you do this You can Never go Back..

I heard the cover of rear bearing gets dry and brittle but might have been a Wiend

lol the rear bearing doesnt take grease or oil its like space shutttle tec lol

Dump tranny fluid 90 weit gear oil only but it wont hurt it but not designed for it

when filling off engine lean forward to get oil over bump to nose pulley

steel ring head gasket silicone front and rea manifold gasket rubber push out with boost

750 or 859 carb 650 is to small

Sand will destroy blower Shouldnt even take it apart unless its broke a friend put 1000000 miles on his and still going 5-7 wheel lol mine 160000 so use your head forced induction needs 0 porting or bigger valves as per B&M even bigger cam

Bubba if it says B&M on front of Blower its a 144 Teflon Bladed Supercharger It makes 12o Hp with 5-7 psi wheel 350 hp 450 Tork on low compression 350 the fill bolt is weep hole that will leak a little allways the oil tank is open so if you turn upside down it will dump all oil out overfill and engine will burn oil over flow and best leave fill hole open till its done leaking and clean oil off manafold or hose off

If you have problems go to old v belts setup on water pump alt and steering dont rev in nuetral or it will blow them off originally the tensioner was on blower snout

Put 90% into your project and 10 % percent to that loud mouth wife ! 😂

Wow wa wee wa

😂 should a named it the Chevy C-Note

Do you need to add thread sealant to the rocker studs? I installed a set of those heads on my SBC 350 and now I am getting oil on all of my spark plugs. No coolant loss and compression checks out good.

Was great to see you again brother Bubba 👍 Not seeing much new from you... did you get the truck finished ? Doing any touring ?

Well, how's it holding up several months later? Looking to buy a cover but so much Chinese junk these days, you never know what you're getting anymore Lol. Thanks for vid

Bubba, Thank you for posting this video. I am rebuilding a B&M 420 for my BBC 468. I am looking for the torque specs for reassembly. Thanks in advance for your help, and thanks again for the blower video.

How many miles per gallon

I was next to you on 170 today. I yelled hey but my Ranger work truck doesn't have power windows. 😂 Deaf ears and all that... Been watching your videos for a bit while I've restored a couple of C10s. Appreciate ya!

Hey brotha question what was the part number for those traction bars?? Or how long are they 28 inches -30 inches? i have a 84 C10 I'd like to install those on thanks in advance and great video brotha

Yup, rebuilding transmission now.😓😓😓😓😓