- 7
- 86 134
Rapid Rebuilds CO
Приєднався 21 жов 2019
DIY how to videos and rebuilding wrecked gems
2021 Benelli upgrades and custom intake build
I upgraded the levers and intake on my 2021 Benelli TNT 135 for less than you would expect. I got some sleek new levers from eBay for about $25 and was able to create a custom intake for about the same amount. If you are into budget builds this is for you.
Переглядів: 174
Відео
First time at Valentine Valley MX in KY
Переглядів 8429 місяців тому
Started out a little slow rolling the jumps since it was the first time on the bike in a long while but started feeling comfortable after a couple laps.
Adding class to your Shock reservoir with an aluminum can wrap
Переглядів 1,2 тис.Рік тому
Adding a little flare to your shock reservoir in less than an hour. You can do this with any aluminum can of your choice.
Headlight restoration
Переглядів 232 роки тому
Tried out the Meguiars headlight restoration kit and was not disappointed.
2009-2018 Ram 2500 6.7 Cummins EGR system cleaning
Переглядів 17 тис.3 роки тому
I will be cleaning the EGR system on my 2011 Ram 2500 6.7 Cummins with Super Clean degreaser
2003-2013 Ram 2500 front and rear shock replacement
Переглядів 32 тис.3 роки тому
I replaced the shocks off my 2011 Dodge Ram 2500 4x4 shocks with some new Rough Country N3 replacements. My truck has a 2in leveling kit and determined these would be the best replacements for the price.
2009-2018 Dodge Ram Cummins fuel injectors replacement
Переглядів 34 тис.3 роки тому
2009-2018 Dodge Ram Cummins fuel injectors replacement
Clutch kit
Now we’re talkin. 🔥
I’ve seen people saying it will overheat the shock is that true?
Nope I have not had any issues with it for the two years I’ve had it on there
You are obviously mechanically inclined but making videos is not for you. Terrible
Horrible video. No real information
If you take the fuel rails off first and get it all out of your way it might make it easier.
This works on any bike right
Yeah as long as it has the reservoir because you can adjust the size of the can to fit bigger or smaller ones
thanks, just bought a 2012 with 126k runs great but always good to know how to do something what youd need
Nice work my guy but if your abke I would delete that truck I have a o8 and deleted it some time ago has 250k and still runs like a new one.Oh yeah 24 mpg on the interstate also
I have to go through emissions test where I live but I thought about it
@@rapidrebuildsco2772 gotcha man
Where you jacked up ? Or sitting on tires?
What is the name of the part in mi ute 7 56? I need to replace that part
Sorry, can you reuse the old gaskets or would it better to buy new ones?
I wouldn’t recommend because then you will get a bad seal and have an exhaust leak.
How long did it take you to remove the egr valve and clean it and then put it back on?
For the Egr I would give it 24 hrs clean and letting it dry good. To remove 30min.
I realize the cleaner you used is probably a little less expensive, but would it be better to use Berryman's carb cleaner in the gallon jug? It can be filtered and reused several times and you don't have to use water. You could make a make-shift container out of an old gallon jug of coolant and let it sit overnight and then just spray it off with the Berry-man's spray cleaner to rinse it off. Just chiming in. I don't own a diesel truck yet but soon.
I’m not sure I haven’t used that before. I used a degreaser and those seem to work good.
How much did you spend on repairs
Thank you, Alex
Good
The hardest part is getting the driver side shock back down into place with the shock tower (triangle piece) attached, the part you failed to show.
Too bad you didn't clean off that valve cover before you installed it. Some of that dirt fell into the motor.............
You didn't record some of the most important steps to removing the EGR Cooler. You jumped around too much.
The valve and filter are easy the cooler not so much. 😕
The injectors don’t need be programed??
They do, those injectors will not be functioning properly, you are supposed to code them with the code that was on the tag.
What is the valve lash supposed to be
Yeah should be .010 for the intake and .026 for the exhaust
That is a seprate video.
What about setting the valve-lash??? Surely u ch3cked it!?!?!
Yeah should be .010 for the intake and .026 for the exhaust
Thanks for the "Quick" listen and saving me some money.
Thanks for the vid. I'm doing this next weekend.
The 07.5 and 08 6.7 cummins is the same. Should say 07.5 - 18 6.7 Cummins
A crows foot may work better
Wow, what a pain in the ass. I thought a sprinter was a pain. Any ideas of how to figure out which injector is bad without a great scanner?
You could disconnect the supply line so the fuel is spraying out a little bit, do it for all of them. If the injectors are working the it will be obvious because the motor idle will get rough. Whichever one you loosen and don’t get any change in idle if the bad jnjector
You might as well replace all of them if you do two from what I have heard. The new ones would out perform the older ones
Hey Alex, great video and good sound. Just wanted to mention one thing that might make your install a little easier in the future. Now this might not work quite as well with your leveling kit, as it does with just a stock suspension, and this is only for the front shocks, but jacking up under the suspension, and then blocking the frame with a jack stand, and then lowering the wheel down would relieve the tension off of the shock so that loosening the nut at the top of the shock tower, (as well as the bottom bolt), would be a little easier. You might have to use a little stool to reach in there. Also loosening the shock nut first before undoing the shock tower nuts and just setting the tower aside, will make it a lot easier to pull the shock out, as well as installing the new one. I've done a lot of these and any time you can relieve the pressure off of the springs is a good thing. I noticed that there was still quite a bit of pressure in that shock, so this might help you. I even raise the rear end and block under the frame in the back as well. It just makes things remove and install a little easier. Hope this helps and look forward to future vids. Thanks!
Loose the loud music
as long as its not rap. I turn off every rap music vid.i mean why just why. tgat wax just a radio station.
My guess is he had some unwanted audio on that part of the footage.
Loud music made me stop Watching before the end. Why?
What solution did you use to clean the parts
Super clean degreaser
useless video because you didn't show how to do it
on 2016 ram do you have to reprogram the injectors ?
No there shouldn’t be any reprogramming needed but you need to make sure the wires that are screwed into the injectors are connected the same way it was removed
Yes he should have coded them with the appropriate code on the tags they came with but it's not as serious as people make it out to be, it's just the optimized code for that injector so they are just running on the previous codes
That is for the assist. Doing the shocks on my dads 2006 and wanted to make sure taking off that little tripod on the front was right. 👍
Lost me at flat brim.