Відео

Great video, great guide (THANK YOU!!). ONE NOTE FOR EVERYONE, for my 2012 Kia Sorento 2WD, that I tripped around for a bit (15-20 min), was releasing the connection for the sensor; there is a metal clip/fastener that sits on the OUTSDE of the connection point (so, toward the opposite side of the car, you can see it, not the wheel side that you're working on). You'll see it, there's a gap between the plastic connection and then there is a metal wire-like clip that holds the connection together (3 sided, slides INWARD and "squeezes" to hold the connection). Just take a flathead screwdriver and pry it OUTWARD (towards the other side of the car (gently). It should slide right out. Make sure you have the other finger on it so it doesn't SPRING outward and fling somewhere that it can't be found. I'm pretty good around cars and this one took me about 1.5 hours (I took small breaks, shut it.......). You'll just need to have some patience, it's worth doing yourself. Got it on Amazon for about $13.

Good

What other transmission from what car i can install in .my 2014 2.5

Talk about the ultimate backfire. So stubborn. Do the job the right way if ur gonna post videos dude smh.

How far away should I be to adjust the lights to the right height?

😮

Is it worth changing transmission after 300k KMS

Cool, thanks

LOL 2:10 The sensor cable was never plugged back into the new hub. To my understanding the sensor is supposed to be programmed to the car is it not what the?

why does the ford manual say the trans comes out with out subframe removal?

Entre para ver como sacaba los tornillos del convertidor pero SORPRESA EDICION EN ESE MOMENTO JAJAJAJ igual gracias por tu video

You didn’t include the most important part………. How to do the actual replacement of the sensor. That sucks

What an absolute nightmare… I need to replace my rear main seal… what’s the average costs to do so?

Okay this is the Front Wheel drive only vehicle. Mine won’t work this way..😢

Rubbish cars from Korea they are shit.

Will you sell the trailer?

How long did this job take?

Can you show where the input and output speed sensors are on the transmission?

Supposed to pull the sub frame all the way out before you start pulling the transmission.

Questions would the speed sensor cause the car not to run good , I have 2 codes that it's giving me , with the rear speed sensor.

I got a 16 fusion that needs a transmission, anybody in Michigan got a good price on doing it for me?

Great video, i’m sitting here at the dealership and they said it was $900 parts included, I wanted to have an idea of exactly what it took to do this work, I only wish I had the time to complete it myself. Exxon presentation to what it would take to complete thank you!!!

Dude just broke his steering rack in the process lol

So if I replace the hub inside the hub is another speed sensor that will make my dash lights turn off because I have the (abs,cliff control,and the car with the skid mark like image) on will all turn off I already scanned my kia and said read left speed sensor faulty will this fix my issue will this fix this issue ??

I’m not a mechanic. I followed this video to the letter. Total success. I will say that the rotor did not come off nearly as easily as this. I had to tap it off as there was some rust and tap the new hub in place as the specs for the size were not exact. All is well. The ABS lights went off as soon as I hit the accelerator leaving the driveway. Great video.

Great freaking video dude!

If you replace the transmission with a used one do you have to reprogram it?

My dashboard lights are again. I’ve changed the left rear couple of months ago. I’m in doubt, is the rights side now or there are front wheels sensors too ? Can anybody tell me for sure ? I looked under the car and didn’t see any front ones, but also i’m not mechanic nor do i pretend i know what i’m doing

Correct me if I'm wrong but is that drum brakes and pads? To me it looks like two different brakes system at the back.

Does the replacement needs any programming in order to work properly? Injust replace my transmission on my 2016 Ford Edge SEL (Same exact model) 2.0l Turbo The reverse, nice and smooth, but on Drive has a slower pace. Any advise?

Thanks for posting the video How many hour of labor would you charge with the cradle removed? Thanks I’m about to remove one of this Thanks again

good day to you. Is it possible to change the abs sensors without changing the whole hub assembly?

The right way is to pull it out with the converter for that I had to remove the entire bumper radiator, fans and condenser then I got access to the intake manifold in order to get to the starter then you’ll have access to the torque converter bolts I rather do it that way than dropping the entire drivetrain lol

I was able to do one without removing the cradle completely. Reasoning being that customer didn't want to pay for alignment because of rack removal. Needles to say next time, I'm going to quote all that in my pricing. I am def removing the complete cradle. F that!!

DUDE YOU NEEDED TO REMOVE TORQUE CONVERTER WITH TRANS. NOT THE WAY YOU DID IT. IT IS NOT LIKE A MANUEL TRANS. NOOOBSSSSSS

That sure looked super easy!! Your music selection is perfect. Nice work

Dang that looked painful!! I did it the same way except I pulled the oil pan off and removed the lower sub frame without the power steering rack. You are very tenacious!! Yea fords suck for that!

I hate fords