Відео

Hi, thanks for reaching out! For any questions you may have, feel free to get in touch with our specialists through this link: www.festo.com/us/en/e/contact-id_59297/ Best regards.

Hi, thanks for your comment! We recommend checking out our PDF on this system at the following link: www.festo.com/media/pim/049/D15000100122049.PDF Alternatively, feel free to visit our website for more information. Regards.

Hello, thank you for your message. You can send a message to our experts through the following link, and they will provide you with specific information about your issue as soon as they receive the request. www.festo.com/us/en/e/technical-support-id_646900/ Regards.

@@FestoNorthAmerica Thanks for your response. I changed the setup to broadcast Telegram 111 and your LV Code is working for me.

Hi Paul, You can contact our specialists directly using the following link. They will guide you in resolving your issue. www.festo.com/us/en/e/technical-support-id_646900/ Regards.

Hello, thank you for contacting us. Please find the link below for various contact options in Canada: www.festo.com/ca/en/e/contact-id_59297/ Additionally, here is the page where you can find more information about those systems, which might be useful to you: www.festo.com/ca/en/e/solutions/collaborative-engineering/handling-systems-id_4462/ Regards.

Hi Philip - send an email to marketing.us@festo.com and we can send you the AOI files.

@@FestoNorthAmerica Done! Thank you.

I'm using a cmmt-as-cs-11a-p3-mp-s1

It’s important that you Restart the CMMT drive after setting the XF1 port to Modbus. Once this is done, you should get online with the drive once again with Festo Automation Suite and confirm you are in Modbus TCP mode and that the Active network settings are the desired ones (IP address, Subnet, etc.). You can check this under Fieldbus > EtherNet/IP -Modbus > Active. If the problem persists, we suggest you contact Festo Tech Support in your country so they can further assist troubleshooting.

Hello, thanks for reaching out! For any technical questions, please contact: technical.support.us@festo.com

Hello, thanks for reaching out! For any technical questions, please contact: technical.support.us@festo.com

😅😅😮😮😮

Initially the SMS series was designed to be a basic and inexpensive way to get into electrical actuators. At this point it is still inexpensive but you can now do unlimited positions via IO Link communication.

@Rick Cameron - Festo cylinders are lubricated for life. In a washdown environment, the cylinder does not require additional lubrication if the piston rod is not extended during the washing process. If the rod is extended during the washing process, a lubricator could help extend the life of the seals. We also offer a special rod wiper seal, made of UHMW-PE, which has very low friction so it can operate without any lubrication even in a washdown environment. This may be preferable to lubricating since it does not require the regular maintenance of keeping a lubricator full of oil.

@@FestoNorthAmerica thanks for the reply. Will the part number for these wipers be in the dsnu catalog?

@RIck - The rod wiper seal that is suitable for use in wet and frequent washdown environments is denoted as -R85 for the DSNU cylinder. For DSNU, this is an option that is not documented in the standard product catalog and must be quoted by Festo customer service. We offer this rod seal as standard with our CRDSNU stainless steel cylinder, it is called -A3. CRDSNU is similar to DSNU but offers higher corrosion protection and a cleaner design. Feel free to contact us in North America for support, at technical.support.us@festo.com or +1 (800) 993-3786. Thanks!

me pasa igual hay alguna solución?

Chale yo tampoco he recibido ningún correo

pudiste resgistrarte?

Hi Tommy, unfortunately due to worldwide supply chain issues, we're trying the best we can to handle our customer's needs despite current lead times.

Our standard HGO offering has a max payload of 50kg and X, Y, Z max strokes of 3000, 1800 and 800mm respectively. Depending on which axes are selected: Toothbelt axes have a repeatability of +/-0.08mm Ballscrew axes have a repeatability of +/-0.02mm. To quickly determine if a standard solution can be used, go to the Handling Guide Online (HGO) page: www.festo.com/us/en/a/8031049/?autoShowConfigurator=true However, if your application exceeds these standard capacities, Festo Customer Solutions can review your application and determine whether a custom engineered solution can be provided. Please contact your local Festo rep for more information. Thanks!