Відео

Built one for a friend yesterday. The self tappers were horrible. Some were bent outta the bag and a lot of the heads kept burning off

Damn good video, thank you sir.

It’s so much easier to assemble them on the ground and pick them up in one piece. You only have to worry about getting each side in the bottom and you are not up on a ladder driving those screws.

Is it okay to store the saw in the vertical position long term? I have found some stands say not to keep the saw on the stand vertically in storage.

Thanks for the video entertainment... especially putting prego mama to work :) --- btw had you used the fiberglass ladder from the start you could have put the uppers on in one piece...lol

I am waiting on lowes delivery for this. I think I am going to assemble the walls and rafters before installing to the rails, though. Watching all that up and down the ladder made me tired.

Building one of these right now, the roof is a bitch haha

The music is too much of a distraction

What’d ya say!

OK, I was just going to hire someone to do it. Not now!

I think it is better to assemble the arches first. With all those drilling.

Are there pre drilled holes or are you self tapping all these holes

Good Video (Skip music next time!) Were you using a 1/4 or 3/8 drive drill?

Thanks for the how too and for not drink bud lite

Will this carport withstand hurricane forced winds in Texas

Only way to finish a project 🍻

My 03 lb7 get like 10 mpg how do I get more I see people Getting like 28

Ok..but for some, best to mute the volume.

Greetings from Australia where I'm about to do mine solo as well, very helpful thanks.

😍 very High Quality!! Great Work

Do you a video on how to remove the dash board, I want to replace the dash since the airbag popped

Excellent single person execution of a possible two person job sir

What’s holding it from blowing away?

Less music. More beer.

Great video, You made it look easy, sir.

Nice video horrible music

Why the jig music?

And that's the bottom line...

Do they need to be full of fuel prior to installing?

Can you share what you used to stick the stencils, paint, wood measurement etc…

Gotta disagree on one point.. I definitely prefer the roof of the truck over any ladder. Lol

what i liked was you did it your self

Thanks, I may have put the bolts in the wrong holes, but I found the directions for assembly poor. I ended up using some of my bolts and nuts to finish the assembly. It seems like a fine cart.

I ran machines for Arrow. In the shop we had to hold a sixteenth. Out in the field they went with somewhere in the area of the two holes.

What’s your favorite spray poly? Thanks!

Lose the music

i just bought one of these stands to go with a new dewalt 78 and this stand wheighs more the mitter saw...pretty sturdy so far...i like it more than the aluminum basic frame that everyone keeps buying where i work

That was a really good assembly video. However, the music sucked big time. I literally turned off the sound. Next time skip the music. Your video was good without it.

How long did this take to build?

🎉

The anchors have been mentioned previously, you didn’t include the tape for the top panels which helps with leaking.

I couldn't watch. 🥺🥺🥺🤪🤪🥴🥴👎👎👎 Assembly ass backwards 😡😡

Is this the 9ft height?

Thanks for showing how it's done (especially the beer-chugging!) My daughter and I are looking to do it ourselves and I wasn't sure if I'd be up to the task, but I think we're gonna do it after seeing you handle it alone. I appreciate your time and effort to share the build.

Please use a mask excess protection never killed anybody

Hi where can you get the wood from

Did this job. Might have been the most difficult auto repairs ever.

How did you anchor it to the ground? Did you have to?

Only drawback was the God awful music. Ty for your time.

Nice!! What did she use so the paint didn’t bleed through?