Відео

The Hose is 2 pieces. You have the metal pipe to the air compressor that goes under the floor and connects to another hose to the air dryer. There is a plate that you have to remove under the floor mat is the best way to get to it.

@whisperingmoments8731 would've never thought to look there. Thank you. I'm having trouble breaking the hose loose at this point. The metal standoff on top of the trans that the hoses are secured to just bends.

Sorry I don't have a way to change it at the moment.

Ate you asking where did I buy them from?

Are you asking

I just bay order over amazon

Good deal

My mistake

@@whisperingmoments8731it’s ok

That's all you have to do is let off the throttle and shift up or down unless you have a racing four wheeler which then you have to use the clutch handle.

I believe the EGR cooler had cracked

You're welcome

@@whisperingmoments8731 I got it though!

I believe that's next to impossible since the MP10 is much larger. The frame I think is wider and the radiator is bigger.

22977101

To answer your question about diagnosis, it's a program that a dealership can buy from Mack/ Volvo. When I said I paid $170 that's what a customer will pay per hour for diagnosis or repair

@@whisperingmoments8731 ok that makes sense. Thanks for your time and cheers.

It's a AHI module. It sends fuel to the 7th injector to burn soot into ash in the DPF

Wondershare (Filmora 13)

You're welcome

The main fuel line how u get it off with out it breaking..?? Don't show it in the video..

@@dionwilliams4496 remove it with a 14 mm and just tap it up. It's a press fit

Because the cylinder liners are above the block

Here is $170

@@whisperingmoments8731 ty

@m.d.40 you're welcome

Yeah it was a bit loud. Will do with headphones on when editing. Thanks 😊

I agree with you...

This was at the Dorchester Shrine Club. Summerville, South Carolina

@@whisperingmoments8731 does this group run with ODBA any

@@whisperingmoments8731 who is the president of this club? Id like to talk to him.

@@scottweathersby6659 I have no idea. That was my first and only time there.

@@scottweathersby6659 Roy Mcswain is the president

Sounds like the dosing valve on the bottom can is dosing too much. Make sure the can isn't cracked at the weid where it bolts on also.

Thank you very much

@@remynajim8070 you're welcome

There is no calibration on the DEF pump or dosing valve

You got that right.

I am trying to put a new one in now and having a hard time getting the gears to line back up!! No damn room

@johnnymac7634 wiggle, wiggle. I usually get underneath the cab with a pry bar to hold it up in the front of the compressor and guide it in from the back with help

Yes. There are 2 coolant lines on the actuator.

thank you sir@@whisperingmoments8731

@@Mack-mi9og you're welcome

What state your shop

Lol 😆 no

I used a regular 14 mm and a extra wrench to pull on it

Sorry. Most people wouldn't do what I do working on trucks these days.

@@whisperingmoments8731 the music overwhelmed what was being said so we couldn't hear. Good to see this new style AHI being changed. I've had to change the old brick style a few times and hated the hell out of it for difficulty reaching it. In this case I don't think they made it any easier putting it in the fuel housing. For one thing when you disconnect those quick-connect lines, a few of them can't be reached with your fingers to squeeze the releases. You have to put a pick in one side and squeeze your finger on the other. Maybe I'm missing a tool. Thank God the torx bolts crack loose okay. Interesting to see that you had to pry for a while to get it out -- that's because a double-O-ring nipple goes into the fuel housing and had to be backed out. Used small pry bar instead of screwdriver. Not an awful job but was expecting to crack a brittle fuel line but didn't

What in the January 6 is going on with the music.

🤣🤣🤣

I just installed the engine after replacing the head off a old engine that blew up

@whisperingmoments8731 I get that but from my little experience is that not gonna cause failure to piston rings and valves??

@codys9601 No I run the same engine for years without any exhaust because the studs rusted off. Engine still had good compression after swapping heads

Sorry I will edit it when I get home

gracias

@@whisperingmoments8731 los más difícil de reparar en los mack son los oil cooler o los fan cluch?

@@renatocaviedes4313 oil cooler

@@whisperingmoments8731 🤣🤣 re malo el sistema del oil cooler . Debería ser como el serie 60. Pero en fin. Buenísimos sus videos . Saludos desde chile

What Is the question? The air compressor just stopped pumping.

Yeah it's a big job. The trucks now are getting redulious with space.

Don't think it will.

@@whisperingmoments8731 the elites are planning on starving all of us are you thick?

@@whisperingmoments8731 after all these years you have learnt nothing and you are still brainwashed by your TV

@@whisperingmoments8731 Bill gates is buying farmland and destroying food processing units

Thanks I love that drone

Its ok just hate the train and some people have lost their minds here

Thanks

Got mine from bestbuy

@@whisperingmoments8731 please give me a drone please 😭😭😭😭