- 33
- 68 648
ME 372 BYU
Приєднався 4 вер 2018
Ansys Improving Figure Output
Working in Ansys Workbench and tired of legend text that is too small to read? Figure resolution lower than you would like? Would you like to get rid of the blue background? This video will show you how to improve the quality of your figures for more professional appearance.
Переглядів: 3 741
Відео
Stress Concentrations
Переглядів 8354 роки тому
Reviews key concepts of stress conentrations and how to use a chart to find a stress concentration factor.
Exporting Deformed Geometry in Ansys Workbench
Переглядів 15 тис.5 років тому
This model shows how to export deformed geometry in Ansys Workbench.
Beam deflection and springback
Переглядів 1,1 тис.5 років тому
Illustrates a simply way to simulate plastic deformation of a beam around a circular mandrel using an applied end rotation. Springback is found by releasing the constraint at the final position.
Elastic plastic Material Creation
Переглядів 5 тис.5 років тому
Shows how to setup a material with plastic deformations in Workbench.
Finding Radial Displacements of Clutch Arm
Переглядів 2,1 тис.5 років тому
By defining a cylindrical coordinate system and plotting the radial displacements, you can get a quick estimate of engagement speeds without the difficulty of a contact analysis. Ansys Workbench.
Centrifugal Clutch Contact Simulation
Переглядів 7385 років тому
Using centrifugal loads and contact to model the engagement of a compliant centrifugal clutch
Clutch Geometry preparation for FEA
Переглядів 3395 років тому
This video shows how to prep the geometry of the centrifugal clutch for analysis. Reviews some basic operations in Space Claim.
Shaft with Keyway Analysis
Переглядів 5 тис.5 років тому
Video provides an overview of boundary conditions, mesh inspection, and results evaluation for the shaft with keyway example.
Meshing Notes
Переглядів 1355 років тому
This video illustrates the use of the mesh quality function to identify the location of poor mesh quality elements. It also shows you how to select the mesh method that Workbench uses.
modal analysis overview
Переглядів 455 років тому
Overview of the Modal Analysis process and key things to watch for.
Large Deflection for modal prestress
Переглядів 1,5 тис.5 років тому
It is often necessary to turn on large deflections in the prestress analysis step when doing a prestressed modal analysis. This video shows you how to turn "large deflection" and shows that the impact was minimal in the examples done here.
Modal Analysis of a disk rotor
Переглядів 4,2 тис.5 років тому
This case illustrates modal analysis of a flat disk similar in geometry to a brake rotor.
Adding a Point Mass
Переглядів 12 тис.5 років тому
Demonstrates that addition of a point mass and its impact on the modal frequency of a cantilever beam.
beam modal analysis
Переглядів 1545 років тому
Illustrates the process of setting up a modal analysis with and without prestress. Compares the modal frequencies of a cantilever beam at rest to one preloaded with a centrifugal force.
Workbench Analysis with Beam Elements
Переглядів 5 тис.5 років тому
Workbench Analysis with Beam Elements
Creating Section Planes to view internal Stresses
Переглядів 1695 років тому
Creating Section Planes to view internal Stresses
Using Workbench Parameters to Study Mesh REfinement
Переглядів 6005 років тому
Using Workbench Parameters to Study Mesh REfinement
Geometry import and preparation for Analysis
Переглядів 1046 років тому
Geometry import and preparation for Analysis
Creating a New Material and Assigning it to a Component
Переглядів 986 років тому
Creating a New Material and Assigning it to a Component
how to turn that on?
thanks for uploading this video. may god bless you |
Can we do the same for Ansys Fluent? I mean exporting the deformed geometry due to UDF and forces assigned to the fluid volume?(In this case the deformed fluid volume geometry)
what if we have a support brace welded with it through fillet weld? ho will we shell that support and the fillet weld?
If geometry is deformed in the x-direction, how to measure the change in length? how to know how much percentage of stretching is applied??
What University is this?
excellent video
I have issue during geometry update, it shows no body to attach
Where were the corresponding strain values defined? I see the x-axis of the graph, but where in ANSYS is the yield stress linked to a strain value of ~0.004?
What is "frequency" in here? Is it when the beam vibrates after that point mass was given? And what topic is this? Is it from Strength of Materials? Because I'd like to know how to do the hand calculations. PS. please someone answer, thanks :D
thank you sir
This tutorial was really helpful, thanks a lot
Thanks
Coud you tell me. What version ansys you use??
What would happen if you add brake pads? Do you add pressures to each one of the brake pads compressing the rotor then follow the same analysis process as shown in the video?
thank you so much this video is really helpful
I am trying to find a calculator to determine the shear strength of a 3/16 keyway on a 3/4 shaft. Any suggestions?
Thank you, quick and to the point
sir i also want to do modal analsys of disk brake rotor...plz help me