Відео

Good job

cho nó tăng dòng bằng cách nào?

Шляпа полная

You indicated that its 1k resistor but in the cct diagram it is 500ohms, how please?

Hello! How to make a 24v, 100an electric bicycle on 220v from a 24v battery to connect a charger and charge a second 24v battery or can you ride or not charge the first battery? Write a response to make a video.

meximam wat ?

ناکامھے

Can I use one of this transistor and its still working?❤

Mạch này làm chơi thôi chứ chạy quạt hoặc đồ điện tử là hỏng đấy

Era o que eu estava procurando obrigado amigo sucesso.

UA-cam alinaldo inversor

Reyl work bro🤔

🇮🇩🎀👍👍👍🎀🇮🇩🙏

Xoay ngược bất tiện, muốn xoay theo chiều kim đồng hồ để tăng điện áp thì đấu nối thế nào bạn?

Nice

Nice video but duration how much

Great work bro❤😊

ممتاز جدا

Show use the output on the scope!

Hello, can i use a transformer rating of 1.5amp for this project

Wrong for more than 500 mAmp. Dont use this circuit.. not safe.. as heating to much. After 800mAmp. Load. I took reading. Its 74C+ heat.

Nice video 👍, this I've been looking for

Good job !!!

كم وات شكرا

What is current rating of transformer

Working but too much hot after using heavy heatsink also. Not long lasting ...

tale me is this real i need for my project

a good idea if it weren't for the glaring errors in the diagram; plus and minus on the extreme pins of the potentiometer and the output to the gate on the middle pin of the potentiometer, besides, the gate must be preceded by a 200 ohm resistor

Ok nice work done ✅👍

You must protect the potentiometer with a 220 ohm 2w or 5w resistor, otherwise when you introduce a load, the potentiometer will burn. The heatsink must be larger when the consumption is high.

omg it works, thanks mate

Fake video 😂😂😂

Transister NPN or PNP?

salve , posso sostituire irf3205 con irfz44n, oppure quale mosfet posso usare.

Can this circuit pass a current of 100 amperes?

thank you so much!!!what is its amperage?

động, động, động .......kkkk

Very Nice

Fake

You can make one of this using any transistor.

This circuit looks like: "flip flop"

If we calculate the frequency, it's about 50khz.. 1÷(2×rt×ct)=1÷(2×10000×0.000000001)=50khz..so,how it's showing only 36khz..can u explain??

Good❤ but what type of transformer you use

How many watts of load will it take?

Rất hữu ích ❤❤🎉😊

Falso, lo hice no me sirvió. Con disipador grande y bombillo incandescente de 12v 21w y se calienta como cautín de soldar 😢. Quiero hacer un regulador pero que hubiera un MOSFET que realidad soporte 15 o 20A y 50w como mínimo. La mayoría se ve hacer y en la descripción ponen 20 o 30a y 150w pero no soporta ni 2% 😮😮😮😮

The scheme does not correspond to what you have shown as an implementation because at the extreme left position of the potentiometer there will be a complete short circuit of the source. The practical implementation of true, but the scheme - not. +Vcc must be on the drain, and the middle terminal of the potentiometer - on the gate

Nice

For 50hz R valiuo

Nice bro