- 154
- 19 976
Kamekanik tv
Приєднався 15 вер 2021
Newbie mechanic duties
Відео
pull down semiautomatic transmission of 6m70 engine(sliding clutch)
Переглядів 325 місяців тому
#sliding #shifttogear #truckwontmove #worksolo #buhaymekaniko
whole process of installing e13c pressure plate and clutch lining
Переглядів 2946 місяців тому
whole process of installing e13c pressure plate and clutch lining
hino truck e13c release bearing repack
Переглядів 776 місяців тому
hino truck e13c release bearing repack
reason why transmission of hino e13c engine hard to pull down
Переглядів 1356 місяців тому
reason why transmission of hino e13c engine hard to pull down
how to replace wheel bearing of nissan sentra
Переглядів 376 місяців тому
how to replace wheel bearing of nissan sentra
how to replace fuei injector oilseal in 6wf1 engine
Переглядів 1336 місяців тому
how to replace fuei injector oilseal in 6wf1 engine
how to tune up hino e13c in short and long method
Переглядів 2896 місяців тому
how to tune up hino e13c in short and long method
paano malalaman na buo o sira ang oil jet rail bolt ng makina
Переглядів 367 місяців тому
paano malalaman na buo o sira ang oil jet rail bolt ng makina
kubota m9450 bakit namatay sa takbo, alamin natin ang sanhi
Переглядів 97 місяців тому
kubota m9450 bakit namatay sa takbo, alamin natin ang sanhi
6m70engine namamatay sa takbo bakit kaya?
Переглядів 1017 місяців тому
6m70engine namamatay sa takbo bakit kaya?
oil leaking in front crankshaft oilseal of 6wf1 engine
Переглядів 558 місяців тому
oil leaking in front crankshaft oilseal of 6wf1 engine
6d22 engine valve clearance adjustments
Переглядів 2,7 тис.8 місяців тому
6d22 engine valve clearance adjustments
mga dapat gawin sa unang start ng bagong gawa na makina
Переглядів 629 місяців тому
mga dapat gawin sa unang start ng bagong gawa na makina
cylinderhead installation and tightening headbolt of V12 engine
Переглядів 739 місяців тому
cylinderhead installation and tightening headbolt of V12 engine
valve sets assembly , at ang paglalagay ng valve seal sa V12 engine
Переглядів 699 місяців тому
valve sets assembly , at ang paglalagay ng valve seal sa V12 engine
full process of adjusting valve clearance in v12 engine
Переглядів 2409 місяців тому
full process of adjusting valve clearance in v12 engine
tamang pagsukat ng piston ring gap ng makinang v8 8dc10
Переглядів 2810 місяців тому
tamang pagsukat ng piston ring gap ng makinang v8 8dc10
pagtanggal ng injection pump ng v8 8dc10
Переглядів 4810 місяців тому
pagtanggal ng injection pump ng v8 8dc10
paano tangalin ang trumpet housing ng Ford5610 at pagpalit ng rear oil seal(pulldown Trumpet housing
Переглядів 4110 місяців тому
paano tangalin ang trumpet housing ng Ford5610 at pagpalit ng rear oil seal(pulldown Trumpet housing
ilan yong torque sir yong pinakahigpit
Ilan ba un boss 2 inches ba?
Pls support my channel thank you so much ❤
Don't forget to subscribe to my channel thank you so much
Pls support my small channel thank you so much
Pls support my channel thank you so much
Yung hino ko kasi pag naka hinto malambot ipasok kambyo pag natakbo na maganit na kailangan pa Isang bumba Ng rpm para pumasok
Pwdng tulad ng case ng ginagawa ko natuyuan ng grasa, o posible po na pilot bearing nyan ay stock up.
Boss saan Ang location mo boss
Sto tomas batangas po.
Kelangan ba mag adjust kahit bago namn ang pressure plate at lining?
Opo para bago pa tumukod ang pushrod at halos manipis na talaga ang lining.
Support my small channel thank you so much ❤
Don't forget to subscribe to my channel thank you so much
Please support my small channel thank you so much ❤
Ang sipag mo sir😊
Thank you po madam☺️kilangan po at d nalubay ang bayarin☺️
Dont forget to subscribe ☺️thank you
Galing idol done watching
Thank you for watching lods
Done watching new subscriber idol
Thank you sa support lods♥️
Please support my small channel thank you so much
Leave likes and comments and subscribe to my channel
Please support my small channel thank you so much
Dont forget to subscribe to my channel thank you so much
Keep up the good work Lods 🤗👏
Thank you po madam sa support😊
Like and subscribe
Please support my small channel thank you so much
Keep it up lods
Thank you po madam
Galing naman lods Pabisita din sa aking kusina🥰
Salamat po
Just leave like and comment and dont forget to subscribe thank you
Please support my small channel thank you so much
Please leave reaction and comment and dont forget to subscribe to my small channel❤
Please support my small channel thank you so much
Please support my small channel thank you so much
Please support my small channel thank you so much ❤
Please support my small channel thank you so much ❤
Pls leave likes and comments and subscribe to my channel.. Thank you
Please support my small channel thank you so much
Please support my channel thank you so much
0.016 inch intake 0.025 inch exhaust
Please support my small channel thank you so much ❤
Please support and subscribe to my channel❤❤
Please support my channel thank you so much ❤
Please Support my channel😊😊😊👍
Reupload at mali ang nailagay kong sukat😂
Same lang po sila sa 8dc11 sir na thrust washer.?
Sorry sir, pero d pa ako nakakagawa ng 8cd11..
Ganda ng gawa mo boss
Thank you po sir❤️
Please support my small channel
Please support my channel thank you
Hi sir..ung 6m70 po nmin..ng aawas po Ng langis xaka my langis na sa tambutso...anu po kaya possible reason?slamat po sa sagot
Valve seal, piston rings, or turbo sir.. Tanggalin nyo po ang exhaust manifold kung may makita kayong basa na exhaust port valve seal po muna palitan nyo.. Kung tuyo exhaust port, sa turbo po kayo magfucos.
Solo flight
Please support my small channel thank you po