Відео

U wanna sell me those tools I'll give u 90

Does it cut square?

Learned how to use the clamp, and I see where the black handles go! Kinda want the stand as well. Didnt know that about the locking mechanism.

Where do you buy oil cooler from ?

Where do you buy oil cooler from ?

Are you in Minnesota and change mine . Good job

Whatever you do, don’t buy aftermarket pressure sensor. They will screw up your fuel pump like a did Mine had to put back the old sensor in and fuel pump stopped acting up until put theBosch NEW.

at $350, might as well just get the dewalt

The screw is a bitch to get out. I epoxied the torx bit into a 1/4 inch wrench. Worked like a charm.

Could you block the coolant line going to the oil cooler, so that it doesn't mix together?

Awesome! Is there a price listed anywhere or an advertisement?

Is it good for trimming?

Just bought this setup. Very happy with it!!! Great review!

half video

Great video. I would only add ONE step. Before installing the new sensor, apply a thin layer of lithium grease on the O-ring (rubber) on the new sensor. My new sensor would NOT insert, no matter how hard I pressed, until I applied the grease.

I bought one today, and still have to buy the stand. I got the saw for 261 with a coupon so I bought the extended warranty, just in case. Probably a waste of money, don't normally buy extended warranties but 90 days was just not long enough IMO.

Do you need to do wheel alignment after changing wheel bearing using this tool?

Hey what electric fan are you using and has there been any overheating issue with the conversion i have the same truck and i love it thank you for the awesome clip

I bought one freaking love it. This saws got them all whooped

Thanks for a no-hype and post-use review. I got one about the time you published this and it's pretty terrific. As with yours, mine was square/true out of the box.

Do you still like saw?

Do another pull, mine does the same thing, it’ll get up a lot faster if it drops into the lowest gear, 4l60e doesn’t like to downshift

Thank you very much for posting!

Mine is bone stock and faster than that

Hey brother if you switch the arms, you will be able to stand the miter saw vertically when it is folded up. Those 2 pegs on the outside of the (right) arm go on the side with the wheels. Its not necessary, but its an awesome feature to have. I hope I don't sound like a "know it all." Great review, I love my Hercules tools 🤙🤙

if you added one more for a total of 2 per side would the weight stick out much past the rim? you can have a total of three but that would look funny

what intake kit, specs

What do you think if you cancel the oil cooler ? Some people prefer cancel it at all especially in hot countries ..thank you

Just a note: 2011 town and country 3.6 takes 5w30, 6 quarts and MO-744 filter. Check your owners manual for your specific vehicle.

😅

My 2011 3.6 uses 5w30 and a different filter....

not going to lie that runs like my stock 5.3 denali trying to see what upgrades I can drop to make my baby a sleeper

Thank you. Very informative

get the ridged rolling miter stand. . watch the reviews on youtube . great stand !!

I also have the 2520. Just curious on your thoughts of why you chose the 3.5" spacer width; compared to 3" or 4" etc. Any thoughts on spacers for the front tires?

I just got a 2520 with the same curtis cab. I would love more into on that stereo setup !!

Thanks for the video. Assembled mine today. I made the same mistake you did, but caught it in time. The roller extension with the "feet", goes on the end with the wheels. That enables it to stand up dolly style.

Do we have reprogram computer or clean out the pipe like the mechanic said to me and take more than two hours to fix it?! He said the sensor i bought is updated one that’s why😅

I have gas in the oil 🤦 2004 XC90 2.9 what is it ?

TELL THEM DARN KIDS TO STOP WITH THE BASKETBALL!!!!!!!!!!!!!!!!!!!

Thanks for sharing this experience , it's very helpful.

Thanks for the video, I’ve got exactly the same situation with my 4.4l v8 xc90. I’m going to order the part tomorrow, I trust that your oil cooler replacement is still working? Also, did the header tank keep catching the oil residue… did you keep washing it out? Thanks again, great video

Love mine. Best value. Size is my only dislike but that was the sacrifice to get durability and power

I didn't crank the engine over enough, and got sprayed. Wear goggles lol

thanks for the video

Nice,hoping I can find a 20-25% coupon soon. Is currently listed on sale (Black Friday ) for $349.99 regular price $399.99

I have the same tractor the same cab I would like to know where did you hook your oil sending unit up at maybe you could do a video on how you hooked your gauges up on your 2520 that would help me out when I hooked everything up with gauges especially the oil pressure one that one I'm curious where you hooked it in and how you did it

Have had this saw for a couple of years, cuts just as good today as it did right out of the box...great saw!

A great video detailing adding rear wheel spaces to your 2520. It will be a help when putting my 3" adpters on my John Deere 2320. Good seeing the before and after pictures with the spacers on too. Love your cab and the fact you got the 2520 too. I'm somewhat curious with your take on running the machine with the spacers on now vs before. All the best and God Bless. 🙏❤🇺🇸

Thanks for the tip on getting the screw out. That was a big help!!!!