Don Hall
Don Hall
  • 7
  • 11 920
Noisy Waterpik Flosser?
Waterpik Flosser clattering.
DIY solution.
Переглядів: 10

Відео

American Standard Toilet Seat Screw Replacement
Переглядів 383 місяці тому
Created by InShot inshotshare.app
Waterway Plastics 711-4050 Ribbed O-ring/Gasket used on 1½" Spa Heaters and Pump Unions
Переглядів 284 місяці тому
Pool filter union gasket: Which way is it installed?
Do Your Chairs Scratch Your Floors?
Переглядів 53 роки тому
Barely worn chair sliders were scratching our new floor. The slider wear was uneven, so a sharp edge of the slider’s base was touching the floor. I used a belt sander to change the angle of the end of each chair leg, so it will lie flat. The sliders even sound better as they glide across the floor. I hope this helps save your floors! Thanks for watching!!
2000 Infinity Fog Lamp Replacement
Переглядів 12 тис.11 років тому
This should apply to 1995 through 2004 model years. This model is Infinity G20t, based on Nissan. The assembly is removed to replace the bulb, so both replacements are covered.

КОМЕНТАРІ

  • @mpmattson
    @mpmattson 2 роки тому

    Were the 55 watt bulbs noticeably brighter?

    • @donhall3423
      @donhall3423 2 роки тому

      I forgot to check, and the car is long gone, but they probably were brighter.

  • @mpmattson
    @mpmattson 2 роки тому

    I have a decent 2000 G20 but found a lower mileage G20t in my neighborhood. All I could find for differences are the heated seats, fog lights and an LSD. (limited slip differential) Is there anything else? Nice tutorial, BTW!

  • @YepThatsJ
    @YepThatsJ 9 років тому

    awesome thanks a bunch!!

  • @Yotafan
    @Yotafan 10 років тому

    Thanks for a tutorial that doesn't take 45 minutes for a simple but tricky task. I'm going to go change them now.

  • @reymundocastro87
    @reymundocastro87 10 років тому

    Thank you for that video you did an awesome job and help me out a lot do you think I can put HIDs on there

    • @donhall3423
      @donhall3423 10 років тому

      I have no idea, but I doubt that the HIDs would be as forgiving as the halogens, with the way the halogen had to be trimmed. It was OK to possibly waste the cost of a halogen if it didn't fit, but there would be more at stake with HIDs. Also, these halogens don't have a standard headlight connector, but have one wire for positive and the base connects to common. I doubt any HIDs connect like that, but ... I could not resist. The bulb base is PK22s, and here is a non-halogen possibility from searching "PK22s base LED" (nothing came up for HID). Good luck! Let me know if you try anything. www.amazon.com/gp/product/B00CXN5Z3Y/ref=pd_lpo_sbs_dp_ss_3?pf_rd_p=1944687562&pf_rd_s=lpo-top-stripe-1&pf_rd_t=201&pf_rd_i=B00CXNLD58&pf_rd_m=ATVPDKIKX0DER&pf_rd_r=1N7V5R01EKEQZQRPNRNQ

  • @reed857
    @reed857 10 років тому

    Hey dude, great DIY. I did this about 5 years ago and forgot how I did it. Watching your video, without pausing :), refreshed my memory and I am ready to attack it quickly. Just wanted to say thanks.