Відео

I don't know why kubota insists on putting the split brakes where you can't use them with the HST? I've got a 2011 Kioti DK40SE and my barnyard is a clay soil base on a bit of a slope, so the split brakes are very very useful! Or when plowing snow, you can almost pretend you have a skid steer. I guess it was the "deluxe" tractor at the time, and its got all the fancy 3pt stuff you want, plus a lever to raise and lower the 3pt from the back.... Kioti is making the NS series now which is basically the DKSE again, fully featured, heavy, and the loader will lift 2700lbs. If your local dealer is good, have a look at them compared to the similar featured Kubota.

First and foremost, thank you for your service. From one police officer (retired) to another. I recently became the newest member of the arrowquip family. The experience has been amazing, and they care about the small farmer. Thanks for the great content...i literally just ordered 2 "j" hooks for the rump bar you suggested. So thank you!

10/11/24, 5;37am EST Great Job and Smart. I like keeping the cattle & other smaller Livestock separate, but together. I've been thinking about having a place to sit when one is about to give birth and also have an area to serve as the feed/med/office/tack/etc room with the WashBay/Grooming/Farrier/Vet/Dental space at the other end where the 2nd garage door can access away from the Foaling Box are so they can drive in and and out while the pregnant Mare is not so easily stressed. I have been researching barns and barn setups for the past few years and now that I am retired I can finally have my Farm. Congrats, you did a Great job explaining why you did this and that. I have been thinking to build a separate temporary Clear Span building with garage doors at both end to keep the gas/diesel/ equipment away from the office and Animals. Making it a pass through design for the tractors, Livestock Box Trailer, 1-2-horse Trailer, Kubota, mower, the 1 ton diesel tow truck, pallet mover, snow plow, etc. My thought is making them both temporary until the permanent barn plans have been approved and built. I am also planning on having a classroom setup for the local FFA and the 4-H to use for the children who do not have the means and place to care for their 4-H/FFA projects. This way, I have more time to get the place surveyed and watch it through the seasons watching for rainwater and snow melt flow patterns and meanwhile get my projects started. I like the idea of temporary building use so that I can have it moved to a different space where it can repurposed... like for a greenhouse & Aquaculture setup, or other use.

Thank you for the video. I have the same trailer, spare tire on the side. I love it and it's a great trailer well built. I have a question if you can help or experienced, I have 06 Chevy 2500HD Diesel ext cab, 8' bed, when I pull this trailer with a load any type of load, logs, material or my tractor, the trailer and the truck behave in a chucking, lurching front to back motion when driving open road or freeway. It happens frequently it comes and goes. Funny thing, this same condition happened when pulling a small rental dump 6x12. I know there are all of the factors of tongue weight, capacity ect, but I have been within the specs. My main question, have you experienced this lurching motion pulling a loaded trailer? Thanks.

Thanks

Im try it the code come on i seen wrong with it im try a new one thanks and let you no thanks for everything 2015 got new been busy up north west side mississippi working to have the same thing a farm and lots more thank you so much stay intouch

Very nice barn! Good luck with Peaches baby!

Good afternoon Robert

It’s easy guys. Stay in school, get a decent job, buy toys, then make money with the toys you buy. Pretty simple

Who ever painted that tire rim didnt sand it before painting it . 💯

Thanks for saving me a trip to the dealership. L3901 with 350hrs with a broken wire to the glow plug post. Realized it when turning ignition on it would blow the 50amp fuse beside the battery. Checked glow plug relay, all good and finally determining it was something at the cylinder head. Very labor intensive, but fixed broken wire, however left with the code. Roberts procedure cured the code, thanks again.

How do I cast a spinner with out getting it tangled

What a great video!! Thanks so much for your business

Wow ! Kidney stones! That doesn’t sound like much fun!

I used to raise shorthorns

Loading livestock never goes smoothly. Some times better than others We have a system for loading out the cattle in the fall when they go back home from here We have two barnyards that join. An upper and a lower We start by sorting in the lower one. The cows belong to two different producers and will go to sometimes 4 different locations.

Good morning Robert and Amber

Does the deck foam stick that gritty paint or did you have sand it down?

Your driveway look perfect before you planed it!!

Nice video. BTW, an F350 crew longbox gooseneck GCWR is 30,500lb when you get a 2wd dually, which I have. Towing capacity is 22,600lb and my 16ft gooseneck dump trailer is 6klb, so payload is 16,600lb or eight tons. I have 24in sidewalls for the same reason as you and could have used a 14ft box if I only hauled rock, but I needed another 2ft to fit equipment.

Use a paint marker to line up ramps on your trailer Great Video

Thank you. I had a P0336 code, and I followed the instructions and it worked.

Holy fuck! Ten minutes of your bullshit just to say jumping related.

Bwllo

I’m on my 3rd Diamond C dump trailer. It’s a 2024. Welds really shitty on the fenders. It trails so nice though with the new Lippert suspension. I would still buy another. I buy at PineView.

Kubota needs to use these tractors in order to know that you can’t push the gas and brake at the same time? I returned my L2501 for a L2502 because they fixed the problem by removing the clutch and shifting the brake pedals to the other side. I need to use gas and brake to take tight turns at the ends of the rows in my garden. The left arm rest/grab is standard (on the 2502) being left handed, I use it. Cruise control is an option, but if you mow a large field, your foot will get tired of being in the treadle pedal all the time (non-ergonomic), it is more of a necessity than an option for me.

Have any of you figured on most likely having to acquire a CDL in order to use a 16ft. dump trailer on the roads and highways? Just saying!

Great video. Very informative and easy to follow. Will definitely try this

Big tex is garbage

Story time

Shouldn't you take it off the boards to check the oil

Awesome build. Curious of the benefits of the beaver tails besides easy entry? Also any opinion on boat plug outside vs inside?

From what I gather, the L series HST was great for you, and you need to buy an MX cab with a shuttle shift to support.

Thank you so much!!

in 2/24, i started looking for a dump trailer and my research began. ive looked at all the offerings in my area, the upper midwest, where pretty much all manufactures are represented. i got to see all these in person and i crawled all over them looking at everything. diamond c had some of the worst welds along with big tex. a smaller big tex dump trailer wasnt even completely painted on the inside of the dump box!!! after a couple months of driving thru trailer lots, looking over the trailers, asking questions and reading/watching things online, i bought a southland sl714-16k dump trailer. $11.5k off the lot and then more for title, tax and licensing. main reason i went with southland is because theyre built different which seems to be a better design. do your own research and make up your own minds. dont know about long term issues if any but right now, im pretty satisfied where my money went to.

Worth less

This a simple issue. You've outgrown your tractor. You shouldn't complain. It's not big enough for you. Sell it. Get a bigger machine. Prob solved. My Grand L 4060, it can lift 2k pallets no problem, its rated for like 16 or 1800lbs but I have lifted wet GA sand that picked my water filled rear tires off the ground and kept lifting the bucket. But what might serve you better is an mx series from Kubota.

Good info . I too was concerned about the Reese goose box if it would work on my cm flatbed with the inset ball. Looks like it will work fine with plenty of clearance inside the box.

If they said they were going to be there at 10 a.m. and it was 18 hours later does that mean they delivered at 2 in the morning?

Top Of The Day hope all is well

Good morning.

Slacker…jk good to see you again

Good luck on the new job. Good to see you again.

Congratulations on getting a job.

I have a 2005 dodge 2500 quad cab slt v8,hemi 5.7 liter, 4wd, 6 1/4 feet bed. I've tried to find the gcwr of my vehicle everywhere without any luck. Online dodge customer service and the dealership told me they can't find it since the truck is too old. Trailers dealers they are all telling me that it is 13500 lbs. Any suggestions on how can find out? I was thinking to contact VDOT since they are the one doing inspections but I'm not sure.

I have PO563 code will this work with high voltage code? got it after jumping and charging with a charger

My drain plug absolutely will not come off.

Great video!

Are loafing sheds typically anchored to the ground somehow? I live in Nebraska and we just got a horse and I've been looking into these. However we do get insane storms that being 70-80 mph winds and hail. How would these stay in place in 80 mph winds?

Great video