- 46
- 1 379 133
Anmol Birring
Приєднався 28 гру 2012
Goal of Birring NDE is to provide NDT Education on a world-wide basis by explaining basic concepts and principles of NDT so as to assist students as well as practicing NDT personnel. Conventional and latest NDT technologies are presented. Students are encouraged to ask any questions pertaining to NDT processes.
Making Phased Array TCG to establish Reference Level on ID and OD notches
The video provides steps to make TCG on ID and OD notches to establish reference level for phased array inspection of piping welds
Переглядів: 1 034
Відео
UT of Welds - Reference Level, DAC and Applying Acceptance Critiea
Переглядів 3,3 тис.8 місяців тому
The video defines the Reference Level used for ultrasonic testing and its application to the acceptance criteria. An example is presented where the reference level or DAC is established on 10 % ID and OD notches and applied on two discontinuities A and B
UT of Stainless Steel Welds - Use of dual element L-wave probe and ID notch for reference level
Переглядів 8718 місяців тому
The video discusses three topics a) applicable wave mode for inspection of stainless steel welds b) use of dual element L-wave probe and c) ID notch to establish reference level.
Ultrasonic Testing of Stainless Steel Welds
Переглядів 3,2 тис.9 місяців тому
The presentation is on ultrasonic angle beam inspection of stainless steel welds. This lecture discusses stainless steel weld microstructure and its effect on ultrasonic wave scattering and propagation. The effect on both longitudinal and shear waves is discussed and the presentation shows that while longitudinal waves transmit easier than shear waves in SS welds, they are limited to 1/2 vee in...
VT of Welds Part II: WPS, measurement gauges and acceptance criteria
Переглядів 9929 місяців тому
This video includes discussion of Welding Procedure Specification (WPS), measuring weld bevel angle, misalignment, weld profile, leg size and discontinuities using gauges. Measurement gauges include bridge cam and fillet go nogo
Visual Testing of Welds Part I - Steps
Переглядів 1,7 тис.9 місяців тому
This video presents steps to perform visual testing of welds. Main steps are 1. understanding of welding method 2. check weld joint preparation prior to welding 3. welding 4. check weld profile upon completion of welding 5. identify discontinuities 6. measure discontinuities and the 7. apply the accept/reject criteria as per the governing code 8 Refer to welding process specification (WPS).
Making Phased Array Scan Plan - use multiple index positions
Переглядів 1,7 тис.9 місяців тому
Phased Array scan plan should not only show the weld getting fully illuminated such as from a single index position, but also show sound getting reflected back from the expected flaws. Full coverage for lack of fusion type defects along the fusion line will require scanning at multiple index positions as discussed in this lecture
Phased Array UT Calibration Table - Piping Weld Inspections
Переглядів 1,9 тис.10 місяців тому
Phased array calibration for Piping Inspection. Upon completion of calibration on ID and OD notches , a calibration table should be completed to show that the amplitude from the reference reflectors is 80 % for all the angles and for all the reference reflectors. The video shows how to complete PAUT calibration table
Introduction to Digital Radiography - NDT
Переглядів 2,4 тис.Рік тому
Introduces and provides requirements to apply digital radiography. The three key parameters for digital radiography are sensitivity, spatial resolution of image and normalized signal to noise ratio.
Birring NDT Phased Array - Reference Level, TCG and Applying Acceptance Criteria for PAUT
Переглядів 4,3 тис.Рік тому
Time controlled gain (TCG) is created to establish reference level on the calibration reflectors so as to apply the acceptance criteria when performing phased array UT. This presentation provides example of using 10% ID/OD notches to set the reference level for ASME B31.3 piping weld inspections. The presentation states that only the reference reflectors as per applicable code should be used fo...
Film Radiography - Key Parameters
Переглядів 2,3 тис.2 роки тому
Describes key parameters of acceptable film radiography that are unsharpness, sensitivity and film density
Angle Beam Ultrasonic Testing of Welds - Shear Wave by Anmol Birring
Переглядів 6 тис.2 роки тому
Steps to conduct angle beam (shear wave) testing of welds - Probe selection, Range calibration, Sensitivity calibration, setting reference level using distance amplitude correction (DAC)/Time Corrected gain (TCG), locate, characterize, measure, and apply acceptance criteria
Visual Testing of Welds Class 101 by Anmol Birring
Переглядів 1,6 тис.2 роки тому
Visual Testing of Welds with reference to ASME and AWS codes
Codes and Standards AWS, ASME, ASTM
Переглядів 3,8 тис.2 роки тому
AWS D1.1 Structural Steel, ASME I, V, VIII, B31.1, B31.3, ASTM 3.03, 3.04, DNV-OS-F101, ISO
Birring NDT Class 112 Radiographic Sensitivity and IQI
Переглядів 7 тис.2 роки тому
Radiographic Sensitivity, Image quality Indicator (IQI) Hole type and wire type IQI, IQI selection and IQI placement
Birring NDT Class 112. Radiography Formulas (New)
Переглядів 2 тис.2 роки тому
Birring NDT Class 112. Radiography Formulas (New)
Birring NDT Class 112 Radiography - Geometrical Unsharpness
Переглядів 3,3 тис.2 роки тому
Birring NDT Class 112 Radiography - Geometrical Unsharpness
Birring NDT Class 112: Radiographic Techniques, Single wall, Double wall by Anmol Birring
Переглядів 11 тис.2 роки тому
Birring NDT Class 112: Radiographic Techniques, Single wall, Double wall by Anmol Birring
Birring NDT Class 206, Phased Array Probe Selection - Frequency and Active Aperture
Переглядів 27 тис.10 років тому
Birring NDT Class 206, Phased Array Probe Selection - Frequency and Active Aperture
Birring NDT Class 202, UT of Welds Part 1 of 2 - CALIBRATION
Переглядів 84 тис.11 років тому
Birring NDT Class 202, UT of Welds Part 1 of 2 - CALIBRATION
Birring NDT Class 104, Ultrasonic Distance Amplitude Correction - DAC
Переглядів 24 тис.11 років тому
Birring NDT Class 104, Ultrasonic Distance Amplitude Correction - DAC
Birring NDT Class 202, UT of Welds, Part 2 of 2 - INSPECTION
Переглядів 115 тис.11 років тому
Birring NDT Class 202, UT of Welds, Part 2 of 2 - INSPECTION
Birring NDT Class 104, Ultrasonic Testing # 1B, Thickness Measurement Calibration Steps
Переглядів 43 тис.11 років тому
Birring NDT Class 104, Ultrasonic Testing # 1B, Thickness Measurement Calibration Steps
Birring NDT Class 103, Liquid Penetrant Inspection # 3, Water Washable Fluoroscent
Переглядів 66 тис.11 років тому
Birring NDT Class 103, Liquid Penetrant Inspection # 3, Water Washable Fluoroscent
Birring NDT Class 103, Liquid Penetrant Testing # 2, Solvent Removable Visible Method
Переглядів 29 тис.11 років тому
Birring NDT Class 103, Liquid Penetrant Testing # 2, Solvent Removable Visible Method
Birring NDT Class 103 Liquid Penetrant Testing # 1 Basic Steps and Equipment
Переглядів 60 тис.11 років тому
Birring NDT Class 103 Liquid Penetrant Testing # 1 Basic Steps and Equipment
Birring NDT Class 102, Magnetic Particle Testing #4, Wet Fluorescent MT
Переглядів 67 тис.11 років тому
Birring NDT Class 102, Magnetic Particle Testing #4, Wet Fluorescent MT
Birring NDT Class 102, Magnetic Particle Testing # 2, Dry Powder MT
Переглядів 62 тис.11 років тому
Birring NDT Class 102, Magnetic Particle Testing # 2, Dry Powder MT
Birring NDT Class 102, Magnetic Particle Testing # 3, Wet Visible Method
Переглядів 172 тис.11 років тому
Birring NDT Class 102, Magnetic Particle Testing # 3, Wet Visible Method
Birring NDT Class 102, Magnetic Particle Testing # 1, Concept, Steps and Equipment
Переглядів 95 тис.11 років тому
Birring NDT Class 102, Magnetic Particle Testing # 1, Concept, Steps and Equipment
Sir please explain in Hindi We are all requesting sir 🙏
Thanks you sir inspire by lesson am ready go for a welding course
Very nice and simple explanation Thank you, Sir appreciate your effort
Make more vedio on tfm n fmc
Nice 🇵🇰👍
Nice understanding n zooming
Sir , clearly tell about standerd
11:04 It's not good.
Good job 👏
Thank you so much
Thank you so much
Thank you so much
Good 💯💯
Helpful sir 👍
Very good perofesor 👍👍👌👌
Thank you
Hi sir good day I need your help ,plz explain ASME sec v article 7, frequency calibration topic
Do you mean - frequency of calibration ?
Mister Anmol, thanks!
Good to know
Great demo Sir.
Thanks
Very nice sir
Thank you
Good morning sir, could you a video for API1104 Radiography and ultrasonic I will appreciate so much I had have been watching your videos you are excellent teacher thank you in advance
Thank you so much for the knowledge.
useful informations , Thanks alot , keep it up
important, thanks
Thanks alot, Very useful, keep it up !
Hi Sir Anmol Birring. I have learned so much from you, since 2018 when I was still clueless about UT. I gained more knowledge from you than the classroom. Everyday after classes, I will go through all your teaching about UT and practices from it. 6 years later, here I am learning PAUT from you, once again. You have been a great teacher. How I wish I could see you in real life to express how gratitude I am to you, Teacher. I wish you good health and prosper life for everything you have done for the NDT communities 😊
Good informations thanks big brother
sir, please make a video on DGS curve for forgings components
What a great and clear explanation amazing and thank you very much ❤
pleased to meet you, my name hendri, lv 2 for ut and MT En 4179
Best
You are too good sir👍
Why the waves will diffraction occur only from tips of flaw not , why it will not diffract from body of flaw
Because of the pitch catch, I would assume that since the sound wave only gets diffracted at the edges/tips of the weld, this is where there is a sudden change in in the material property which would be picked up by the receiving transducer, The body of the flaw is more uniform than that of the tips and/or the sound does not make it to the receiving Transducer so there is nothing to detect from the body... hope that helps
We all are blessed by your kindness ❤🙏
I'm new to UT inspection so forgive my ignorance but I really like that first leg/second leg set up do all UT detectors have that option?
Good morning, query. When I have to x-ray materials such as aluminum, what indicator do I use? If you can tell me where to look, thank you
Gracias por la explicaciòn :)
pls make some video about wps qualification and welder qualification as per asme and aws
An echo that rises ℅20 (-14dB) above the reference curve is evaluated. It is not accepted, but its length and characterization are examined. Crack, LOP and LOF are rejected.
Sir please make a complete video on Eddy current NDE
Great presentation. Your presentations have helped a lot JN my NDE ;UT and ET; journey. Much appreciated. Thanks
Hello, could you say something about DGS technic ?
Then which is preferable to use notch or drill hole for sensitivity calibration with L waves.
Excellent
Well, explained.
Hello sir i am struggling for RT film interepretation please explain video how to select defect level and defect marking
DAC doesn't compensate for the attenuation of sound as it goes further into the thickness .. realistically ?
Primarily it is loss from beam spread. Carbon steel has very low attenuation
Sir very nice and understanding the class excellent sir
Thanks
level 3 classes ?
Are u Running any institute?
excelente video
How does one remove the weld cap w/o causing damage to the weld metal in the process of removal?