Відео

gracias por tu consejo!

Hello! Thanks for watching! Yes, on our www.cetgroupusa.com website this item number is 501012

hello, The heater plate does not have to be replaced with the fixing film, it mainly depends on whether it's worn. If it is worn, please replace it. Generally speaking, there're two ways to decide. a, whether plate is worn; b, see whether the grease on plate is dried, turned black, or blocked, if there are conditions like these, please replace the plate. Hope this information can hep you!

hello, yes, this will work for Konica Minolta Bizhub PRESS C1060, Bizhub Pro C1060L, Bizhub PRESS C1070, Bizhub PRESS C1070P, AccurioPress C2060, AccurioPress C2070, AccurioPrint C2060L

hi, please email sales@cetgroupco.com

we will add to our to-do list, thank you!

Thank you for your question. Please note error 50.22.00 means the machine does not detect the heating element is warming up. Following is the troubleshooting procedure: 1. After getting the error check if the fixing film is hot or cold. If it is hot, then the likely reason of the problem is that the thermistors inside the fuser unit are dirty or not properly seated. Reassemble the fixing film assembly making sure the thermistors are clean and properly seated. If the fixing film is cold, then proceed to step 2. 2. Check the resistance between fuser unit contacts as it is shown at 8:53 in the video (the normal resistance for 110V fuser units is lower than showed in the video). You will likely find the circuits are open. If so, you will need to find where the circuit is exactly open: o The heating element connector is not fully seated o The thermoswitch is open o The heating element is installed in wrong direction o The heating element is broken or defective Thank you for your interest!

Yes we do! Please contact Emma@cetgroupusa.com for more information. Thank you

You are welcome!

Please tell us your geographic area and we will send you the email address of your representative. Then they can help you. Thank you for your interest!

Hello, Very likely you made a serious mistake when disassembling the dum unit. You removed the two screws that hold the arm-spacer on the front support plate. The location of the arm-spacer is factory-adjusted to keep the proper gap between the OPC drum and the developer roller. If you remove (or even loosen) these screws and reinstall (or tighten) them, you break the adjustment. Now you may loosen these screws again, move the arm-spacer all the way toward the developer roller, then tighten the screws. This will prevent developer pulling, but you may get lighter image on the front side of printed pages or horizontal light banding at about 1-inch interval because the gap has become too big. You may try to fine-adjust the location of the arm-spacer but it is very difficult to catch. The best way to solve this is to buy a new drum unit. Good luck!

​​@@CETGroupUSAInch my God , that's true Sir. When I was disassembling the drum unit, I removed the two screws that held the arm-spacer because some videos I watched on UA-cam did it that way and from what you said, I can understand your point very well. I never knew it is way risky to remove the OPC drum that way. Now that I know, I won't remove the drum unit that way again. Thank you sir. I will try what you have just said. Sir, that means I will need to bring out both the developer unit and drum unit in order to get a proper measurement when moving the arm spacer of the drum unit towards the developer roller ? Secondly when I was servicing the drum unit, I used a white piece of cloth to clean the edges and side of the cleaning blade. According to your video, if I am reusing the Cleaning Blade I will need to apply toner to the edge of the Cleaning Blade. If I don't do so, will it have any effect ?

@@CETGroupUSAInc wow thank you sir. It work! I mean the adjustment of the arm spacer. Truly it was a big big error from me. I tampered with all of the arm spacer in all of the drum unit. I had to call an engineer who helped me to adjust all of the three arm spacer for Cyan, Magenta and Yellow. Now, the developer doesn't spill developer to the OPC anymore. It seems balance now. Thank you sir for the idea. I knew I must have done something wrong but I didn't know the exact place that I got it all wrong. I never knew that I messed up the arm spacer for the drum units. The engineer also spot the errors I made while fixing the arm spacer. He told me the same thing that you told me, "NEVER TO LOSE THE SCREWS OF THE ARM SPACER BECAUSE THEY ARE FACTORY FITTED AND ONCE TAMPERED WITH, IT WILL TAKE A LOT TO WORK TO BALANCE IT BACK". Truly it gave us a tough time to balance it back. Thank you so much sir for the idea. "YOU ARE A GENIUS"

@@gabrielchristopher9363 That is great that you solved the problem and we were happy to help! Regarding your question about drum cleaning blade lubrication, If you don’t apply toner to the edge of the reused drum cleaning blade the cleaning blade may flip during the machine getting ready or when printing the first several pages. If that has not happened, than it should be ok.

@@CETGroupUSAInc wow thank you sir for all of you contributions and solutions. Am more than grateful sir. Now I understand how to remove the OPC drum, and the reason why toner is applied to the edges of the cleaning blade for both drum unit and image belt. I had the same experience on the image belt. I was wondering why after cleaning and installing it, the cleaning blade of the image belt flipped but I have solved it with your solutions. Once against sir, "YOUR ARE A GENIUS"

Yes, all toners are tested with OEM toners to ensure full compatibility and comparable performance. However, we cannot guarantee compatibility with other compatible toners since we do not know their formulas. Please let me know where you are from and I will give you the email address of your CET representative. Thank you.

Please contact paola@cetgroupusa.com, your CET sales representative for the requested information. Thank you

Thank you!

Very good 👍

Thanks

@@masengeshoflorence7027 You're welcome!