Відео

Thank you so much for this video and your accurate instructions and suggestion. The fix worked great and it helped me save a wonderful machine.

I have an s10. There are two smd parts marked as R??? (Forget numbers.) And have a zig zag resistor symbol on it. Suggesting they are resistors. They are both open. Im thinking thermal fuse ? Is that right. Can i just short them

Danke, genau das was ich brauchte 😀 !!!

Thank you ! This really helped and I fixed my robot!

Roborock S6 MaxV. Docks, says charging but never does. Now the battery is obviously totally dead and won't turn on. Changed battery but still the same. Never had Error 13 though

Hello, tks for your great work. I replaced the fuse but after I done the robot start to charge for some minutes then it can't do anymore. I had to wait some minutes and then it can again. So I was suspecting that it was due to broken fuse. I then removed the fuse and shortened using wires. But this time the robot can't charge at all. The strange thing that I note is that the positive and negative poles of the red and black wire coming from near the fuse seems shortened but I think it is quite strange. Could you help me?

Jesteś wielki!! 👍 udało się naprawić😃 DZIĘKI, 👍👍👍

Wird root benötigt?

THANK YOU!!! 🙏 This fixed my machine.

szkoda ze nie widać operacji 😢

u mnie wskazuję 4.20 na stacji to za dużo?

Hi @bastelbank5855 after i change the PTC fuse, i have another problem that may or may not be related to this and I would like to ask your expertise. My roborock is not charging and the dock always have white light. The dock is 4.1V when not attached to the robot (so it's fine). However when connected to the robot, it starts to drop slowly approaching 0V so I'm sure it's not a contact problem. So it didn't jump to 19V. The battery seems fine as it's in 12.5V. Do you have any idea what went wrong and what could i possibly do?

I changed the fuse and it didn't solve it, but used this video twice, once for the fuse and the second time for the motherboard. You're a legend!

Was ist bei QF2 für ein Bauteil? Rechts neben dem Kondensator vom Anschluss des Vakuum-Motors, meins ist abgefackelt und ich muss es neu kaufen. Typenbezeichnung wäre super. What is "QF2", right from the Condensator of the vakuum-motor. Need to buy this new because its burned down on my board.

Около кнопки слева кусачками выламываем там этот предохранитель, перед этим просто декоративную пластину сдераем вот оно!

Не надо его разбирать, просто кусачками или паяльником выламываем отверстие и даже не выпаивая старый навешиваем новый предохранитель, ура два года ещё поработает, потом уже в программе робота заложена СМЕРТЬ!!!!!!

Там на материнской плате есть самовостанавливающий предохранитель, он подыхает первый, вторая деталь уже в блоке зарядки , это конденсатор в горячей части, дальше я ещё не лез у меня роборок6 ему уже 6 лет. Самый косяк это защёлка мусорного контейнера она рассыпается а в запчастях в продаже нет.

Am Macbook geht es dann wohl auch nur wenn man Jailbrake hat? Android habe ich nicht., Nur noch Windows

Thanks a lot

Hi Everybody! I have Roborock S5, and the charging is not working, the vacuum cleaner always come off form the charger. How can i find out if the charger is the problem, or the battery or the vacuum cleaner mainboard? Thx in advance!

Instant like when you mentioned MacGyver :D Mine's got the same error, hope it's just the cap in the docking station as I just had the robot disassembled the other day to root it and install Valetudo.

Habe gerade nach der Anleitung die Sicherung getauscht. Geht wieder - vielen Dank. Kleiner Tipp: in der Nähe der Stelle auf die in der Anleitung die neue Sicherung zeigt, ist am Gehäuse ein Abstandhalter zur Platine. Wenn die neue Sicherung drunter liegt, merkt man das vielleicht erst, wenn der Bügel des Anfahrschutzes beim festziehen der Schrauben schwergängig wird. Ist die Sicherung schon eingelötet und man hat einen Abstand zwischen den Gehäusehälften muss halt der Seitenschneider zum einsatz kommen. Dann passt alles.

junge putz dir mal die Nase. Kriegst ja zuviel

Hab heute die Sicherung getauscht. Beim erneuten Laden dann wieder der gleiche Fehler 😩 Hast du eine Idee was ich noch machen kann?

SUPER

Just changed the capacitor in the dock to no effect, so I guess I'll do this now, good video.

Thank you for the video. My roborock works again.👍

Super Anleitung! Heute habe ich den Fehler genauso behoben, Zeitaufwand etwa 3 Stunden, mit Aufschrauben, Auslöten, Einlöten, Zuschrauben und das ganze Werkzeug wieder im Schrank verstecken.

Today, with you video I've fixed my Roborock. Thank you for great description!

Thank you so much for the guide! I accidentally damaged the component next to the fuse when I tried to clean up the contact point, totally avoidable mistake. Fortunately I bought a second hand motherboard with a damaged fuse for $3 and redid the process. This time it worked like a charm!

Hello sir, I've made everything like in your video, still the same, robot is just driving avay from the chargin bay saynt to clean the contacts, 1st time at 65% than at 85% and last time at 90% of battery charge, Could you help with additional tips please ?

This fixed Error 13 on my Roborock E25, thanks!

(Mystery) Hello just to say that I followed the firt steps to check and replace the Capacitor in the Dock ( 68uF, 420V). I dismantled it then I discharged it, and then I tested. The test was negative. The capacitor was working well!!! So I installed it back. I took the advantage of the dock been open to clean it a bit. Guess what! My robot is working well again!!! What mystery! May be discharging the capacitor has something to do with this…. May be it gets loaded … and there is an memory effect that makes it not working well at some point and it needs to be discharged… So may be it is not well sized and a different size need to be installed instead… even if working well. Will wait, if the issue appears again, I will replace it… may be with the same on as in the video.

Guten Abend, übernimmst Du zufällig Reparaturaufträge? 😅

Imho muss man die Schrauben unter dem drehenden Frontrad auch rausschrauben ...

Thank you. Excellent 😊. Most helpful part was the removal of every screw. I replaced with smd 1.85A 2920 fuse. Remove with two soldering irons, one on each side at 400 degrees C, if you don't have hot tweezers, which I did not have.

replaced it with a copy of the original component instead and also worked fine, the resistance readings were all quite random so not really sure it is the proper way to measure them.

Bonjour. Merci beaucoup ! Je n'y connais rien en électronique mais votre tutoriel a été salvateur. Grâce à vous, j'ai pu réparer mon appareil. Sans quoi, il aurait fallu le remplacer, et là, pour 0,25 €, il redémarre. Merci à vous pour mon budget et surtout pour la planète. Merci, merci, merci !!!

Hello? The error disappeared after the fuse replacement, but the wifi doesn't work. Can you guess the cause?(Wi-Fi led doesn't turn on and doesn't appear in the search list at all.)

thanks

Besten Dank für dein Video. Mein Hoovy ist wieder am Start. 👌Die nächste Robo-Investition kann noch warten! Eine kleine Spende ist unterwegs.

Thanks man! Yor video was exactly what I needed!

I need an error code for checking, please.

Thank you so much for this video! I fixed my robot this way and it's been working great (I cheated a bit as just soldered the new fuse over the old one). After working well, today the robot was completely dead. It had parked by itself in the charger yesterday. But today no life. Cannot even do a factory reset. Could it have something to do with the fuse (my bad soldering?) again? Or where should I start looking for faults? Charger shows 4.2 volts.

Thank you so much ! Great video, it solved my problem so far 👍🤞

After following the advice the robot unfortunately won’t even start charging now 😭 I guess I screwed up something

Great Video, it helped me a lot. Thanks!

Thanks, struggled a bit removing the old capacitor but got there in the end. Great tutorial.

Why not just solder the new fuse to the connections of the old fuse? cowboy move for sure, but electrically it would work as they would be in parallel.

Hello! I tested my voltage with the roborock on its docking station. It hits around 2 volts, bounces around and hits zero. Then repeats. What is at fault here?