Відео

It seems so obvious once you know it, yet I couldn't come up with this in days.

Oh cool, I thought I wouldn't be able to do this without a table saw. Thank you!

Do you apply The Danish oil before staining and varnishing?

Mix water and another

thank you !!!!!!!!!!!

Thanks for posting the video (2 years ago!). Still relevant and useful. I am trying to cut a straight edge on a narrow piece of wood (3"). I only need to shave 2/8" off both sides, but It's tricky and I haven't worked that one out yet. Oh, and no table saw, but have a jig saw and a circular saw. Thanks again for posting the video and taking the time to make it.

Thank you

Thanks so much for the excellent idea - can't wait to try it..!

Worst spent two minutes of my life.

Thank you so much for sharing your knowledge with us! I'm very thankful to you. Best Regards, Tom Pollock

This won't work if the board is not flat already.

Thank you for this video! What kind of guide is this? Is it specific to this brand or can it work with others? Thank you!

Whoever is looking to square a board don’t use the method in this video instead lay a level on the side against the a table saws rip fence and but your piece of stock beside the level and start your cut

Quit UA-cam.

It is really really hard to cut the board free hand straight.

Absolute rubbish! There is a reason the teeth on the blade are 'set' at a particular cutting angle. You don't even register as amateur.

I was thinking more of what Americans call 2x4, perhaps to remove curves.

Is it water resistant or waterproof

LOVE THE MOVING CLAMP TRICK!

Is this the best and safest way to do this? I’ve been trying to sand a taper into strips on the belt sander and it takes way too much time and effort and too much sawdust. I’m new to the table saw though so I’m hoping this is a good option for me.

I love Danish oil, it's my go-to for many simple projects. Also doesn't require prestain conditioner, one less step to worry about.

Yeah... this doesnt work. Carbide can only be shapened by diamond and sandpaper is too soft.

Easy enough. Presented simply and clearly; should keep me from overthinking and confusing myself. Thanks for the instruction.

I just cut 4 of my fingers off trying to do this

I tried to cut the edged of a board with 45 degree angle, 1st. my clamps holding my guide got in the way. 2nd. the end of the cut tore off because the end was unsupported, but that's how all the other UA-cam videos show it. done. they have the wood dangling off the edge of a platform on a sawhorse and let it drop, so I did the same and the very end came off before the cut finished and ruined the cut. YOu are the first to say that the whole cutting surface should be supported. I dont' have any sacrificial board as I only bought what I needed. I guess I'm screwed on this project from the start. Thanks for showing the correct way. Too bad I didn't find it till AFTER I made a bad cut.

Water based polyurethane is garbage.

You'd be lucky if that method could sharpen a bar of chocolate!

“Smoothen”? Really?

What cleaning solution ?

How do you stain wood filler --- if you don't want to stain the entire floor? There are gouges in my hardwood floor. I want to stain wood filler so the color matches, then insert the wood filler.

very helpful, far better than other vids explaining the process!

I'd rather see a white man change the blade.

When I searched for How to cut plywood with a circular saw I didn't expect that half of the videos were just ads for tools. Silly me.

Bro... You didn't sharpen it. You cleaned it. Ffs

Thanks. Nice a simple explanation 😊

No one has foam like that

I have chisels but I am terrible at using them. I finally got my dream of a woodworking shop of my own but have to figure everything out myself. It would be a good comedy show. But if you have any advice, I am planning on making headers for my windows suing what I have on hand, which is not a router...yet.

Can it cut straight down the middle of that piece of wood?

Tak

Good video

Super helpful thanks so much

very good. i just made lines all the way and free hand sawed with a circular with clamps too. i got 8 strong stakes for my garden from a 2x4. so easy and cheap!!

I like this technique. I HATE the robot voice.

I love the simplicity of these videos. My sacrificial wood is dusted off and Amazon are bringing my Dewalt circular saw today to begin my wood flooring. I’m feeling trepidatiously confident so any tips, including using the dewalt guide fence with 20mm tongue and groove appreciated, as my very first circular saw cut EVER needs to be a 7cm engineered board rip😅 😥

Brilliant! How easy... worked great to make my table legs...thank you....

This saw blade I think the effect is average, and kunlun tooth diamond saw blade compared, or a little worse

Basic, simple, and to the point. Thank you!

Who has a big piece of foam??

This was exactly the process I have been looking for to cut a long taper on a furring strip. Perfect!

Thank you!