Відео

Sir want to see your control circuit of 12 leads

That inverter board looks the same as the LG multi v board

Very clear Thank you!!

Hi there we have 6 of them units on a building an we have nothing but trouble almost every unit have blown compressors and can not find a solution any ideal

How do you actually get to the Daikin fan board in the emerion?

Great video. Do you have to shut the condenser off to check the wet bulb? Thks

Seems like every video like this glosses over the most important point of figuring when to add/subtract refrigerant in a few seconds, and then takes a minute talking about cleaning the filter.

Is that temp chart valid for r12?

Is it possible to get a recording off the service checker and put it into a file to then be able to put it into an email

Nice video thank you

I have the same Issue, headed out to clean one this morning.

Hello there. Can you operate the oil pump and guide vanes to test their operation when doing an annual maintenance on the chiller? Thanks.

Thank you so much . This helped me fix a WSHP.

Good video, there are a few drawbacks to the H10- just remember to stay away from wet coils, as the air pump will suck moisture into the heated diode and cause problems, making you have to pull the sensor out and dry it out with nitrogen. Another issue is the sensors tend to wear out and need replacing after a lot of use. The little leak calibration bottle will leak out and evaporate quickly in warm climates. I use infrared leak detectors nowadays as you don't need to worry about moisture and the sensors last a very long time. I have over 40 years of experience in the trade and started out using the H 10 and many techs do agree that its a great unit.

Hello can make my hermostat to shut off at 1 ° difference from the setting that I have it indoor?

Can Explain how to connect with tayp 3

Thx

What size are the two screws that hold the feet?

🎉important info man

I’m very new at HVAC and this helps me understand better. Great video thanks from all of the newer people getting into the trade 👍🏽

Good evening Bryan, may you kindly advice which of the Daikin external VRV unit model can be controlled with the BRC1E73 Remote Controller? I would really appreciate your advice.

Excellent video guys!, I’m a mechanical engineer visiting your channel for the first time and I just subscribed!

Good morning sir quick question where is the best place to get these value ranges

Can an R22 system with an original piston-type expander be converted to TXV when a new evaporator is installed?

Really nice video, from a Florida Daikin rep.

Wow awesome explanation. Thank you.

I want to know the order of stacking the reeds in the reed valve... this doesn't show that.

You're not even going to test the groove by putting a fitting on the end and checking fit?

Super informative video, and these guys seem super trustworthy. Appreciate it!

What will pickup R422b? I wonder. I'm converting over but expect future leaks.

Hi

Great info. Thank you , Craig

You people are amazing ,the explanation its really understood correctly thanks

Good work weldon

We will be looking into this. York is now locking us out of optiview equipment.

Great video Jeff! Thanks for putting this out here.

Why why all this videos don’t show the actual detail wiring

I do not understand here...isn't an inverter circuit ment to convert DC to AC...!!!! The scroll compressors I've seen on Heat pumps eg..Toshiba SMMS-i versions are rated with DC Voltage ...Please if coild clarify for me as I am still a rookie ..Thank you

I have a compressor that's dead. And now it's time to replace it and I really don't know how. It's a Daikin VRV IV. I'm From Namibia 🇳🇦. Can you please help.

Thank anh.anh co the cho em quyen sach do duoc không

I have been working on Dakin VRV Systems for over thirty years. Never had an issue when going into recovery/evacuation mode. It's critical when you want to work on a system like a compressor replacement.

Daikin recommend 15°

Good

There is silver on the contact points....be very careful of using an abrasive. If you wear off the silver....the points will get very hot and very fast.

11:29 - On a burnout repair I could justify replacing the liquid receiver, also. How else would you get the burned oil out of the receiver?

Please your number please I need some part to buy

Excellent, interesting, informative and fruitful for all those whose are concerns with HAVC. Welldone.

I am already professional in HVAC, I really appreciate for suchlike informative and fruitful explanation for all those whose are in this field. Welldone. Keep continue likewise.

Thank you 🙏🏼

How would you go about changing the rotation of open transition wye delta (480v)