Відео

How did I just learn Adam Krefting was the founder of Cush Core? I followed Kreft Moto for years, until around the move out of Colorado. My dirt biking has ceased (for now) and MTB became main hobby. Worlds colliding.

Do a tutoral for dh case

Poor review due to the speed off completing the final bit of seating the tyre!!!!!!

soapwater is great! put your tires on a warm location, it‘s much easyer to install

This video should be nominated for a Nobel Prize for ending so much suffering.

If you cut your sidewall bad is their still room to sneak in a tube with Cushcore installed to ride out?

heck of allot easier than putting insets and tubes in a tire, always get the insert wanting to roll to the side and not stay center.

I don‘t know if I‘m too stupid or if it‘s the carbon rim, but I worked for an hour now on the tire and still the last bit of tire is just laughing at me and showing me the middle finger

Just gotta be able to put them on 😅

Funny clip

An old car tyre works well as a substitute trash can and is not going to damage any rotors or spokes.😊

Thanks!

This is the best cushcore video I ve ever seen.

I had a lbs install cushcore now both wheels wobble. Took it back to lbs and they tried again but wheels still wobbly need help

The hammer/ rim method I found highly unorthodox. The biggest help for me was PRE-STRETCHING the Cushcore before starting. I found this video to be ok but not applicable for “everyone to do at home”

Y’all should be ashamed producing such a shit video update it

Fuck this Shit

2,5 hours on Kenevo, but good :)

Why make this video if you still won’t even use a new tire?

Yeah you guys suck. I think if you’d have made the video even remotely realistic I wouldn’t be so pissed off, but instead you just sort of blatantly lie about the three hours and 3 pairs of hands you actually used in between takes. Today was my first tire change for my one and only cushcore and I ended up just throwing the cushcore in the garbage instead of struggling with it again. If you had made a realistic video, I wouldn’t talk every one of my buddies out of getting one. 🖕

My Garbage Can ist broken… no way to Get in the Tyre lever

This is around the point where you realize cushcores arent worth it

Ha bullchit these are a pain in the a$$$ but worth it on the trail. I for the life of me can’t break the bead!

Didn't help one bit still cant get it on. I probably just have to weak fingers. Eff 😢

This should be the first video shown, It helped me get my tire on the rim. It does take some strength still to get it on the rim.

deepfake!

Great video, I know this could be frustrating. That unit I literally gave up and took it to the bike shop. The secret weapon/tool here is literally the garbage can bahahaha. Boy did I felt stupid 🤦🏻‍♂️ Just became a customer so let’s see how it goes. I wish the air valves would come in different colors, or at least in black. Kinda pricey but you get what you pay for, right!? So expecting good results 🤞🏽🤞🏽🤞🏽 Thank you!

es una mierda montar ese cush core..!!

One tip for getting the tire off the bead. Use the tire lever as shown but give it a light tap with a rubber mallet. Worked for me, where doing it by hand wouldnt.

Thank you for the tip to push the bead into the center of the wheel. That made all the difference and you’re the only person to suggest it! Thank you

Save time if you're swapping out new rubber.Just cut the tire off, right down the centre all the way around, remove cushcore, then the two halves of the tire. Waaaaay easier. My tire was glued to the rim and the method recommended here wasn't cutting it. Lovely product but needs some installation/removal refinement.

you didnt take the tire off the rim? How you will you get the tube out? All I saw was some nonsense.

Jacob never disappoints, this is unreal!🔥

Jacob never disappoints, this is unreal🔥

Nice job Jak,

Filming on point 🔥

🤘🔥

Jacob g 123 🤘🏼

Such a sick edit, Love my Cushcore

🔥🔥🔥

It can be ungodly frustrating but it can be done. If you get frustrated, take a break. Don't be like me. I tried forcing things and wrecked the rim removing my rigid DH tire with a wire bead. Also bent two tire levers in the process. The issue for me was that it took a ton of force to break the bead away from the rim, and after doing so it would pop right back into its slot when I removed the tire lever. What worked for me was using 3 sturdy DH tire levers. I pried the bead away in three spots close together, leaving the tire levers in place to keep the bead from popping back. Then removed the middle one and moved it to the outside to pry more of the bead away. If the bead pops back into place when you remove the middle one, pry it back and stuff something in there to keep it away from the rim. I kept repeating this until the bead was around 50% separated from the rim, then it started to get a lot easier to push the tire away and the bead stopped trying to reseat itself. Once the bead is unseated, it's just like removing a tire without the insert.

There’s no WAY you have a core fitted in that video

CushCore is amazing. I have them in all my wheels.i just starting using in my new gravel wheels and they are so nice. This is the best upgrade I have ever done to my bikes!

Thank you for being so considerate with your coustomers ❤. Everyone told me cutting my tyre was the only way. But this video really helped me. I would personally recomend using Maxxis tyre levers and gloves.

just buy a tannus insert. way easier. im running a tannus on the front of my DH bike and a cushcore in the rear ( which i bought out of frustration at a bike park before i bought the tannus) and the cush core is always a royal pain in the ass and the tannus is always super easy

Add the sealant element to this battle, round 10 fight!

No matter what you do, cushcore it’s incredibly difficult to install. No even my LBS wants to touch them. I am sending mine back.

It's all about the trashcan 😄I will be going to Walmart tomorrow morning to buy one 😉 Thanks 👊

What about soapy water and sealant? Cant imagine that bein a good combo

this is the only video worth watching in youtube for this installation. the rest are just clowns...