- 36
- 2 008 635
WOODIE
Приєднався 21 жов 2023
SECRETS FROM THE PROS How to make a concrete path so that it doesn’t sink into the ground and crack?
Step-by-step instructions for making a concrete path at the dacha
If you do it thoroughly so that the path is really strong and does not crack, then it is worth doing so.
Clean the place. Remove the top layer (turf) with a shovel (depth of turf removal is about 14 cm). If you don’t want there to be puddles on the concrete surface, then you need to make a slight slope. For example, for every meter the slope is 2 mm.
Make formwork. It can be lubricated with detergent so that it can be easily removed after work.
Then geotextiles are laid. But I think I can do without it. Pour sand with crushed stone fraction from 5 to 20 mm.
Sprinkle well with water and compact. Then spread a plastic garden net. You can buy the cheapest one.
Then lay reinforcement with a diameter of 6 mm. You can do it without reinforcement, but add fiberglass to the solution. I also heard from professionals that it’s good to add a plasticizer to reduce the amount of water in the solution and then the concrete becomes especially strong. But I think I can do without it so as not to spend extra money.
Proportions
Fill the rough layer with cement with the addition of crushed stone. For a bucket of cement (grade 400, 500) there are 2 buckets of sand and 3 buckets of crushed stone. After pouring the rough layer comes the finishing layer (mortar without crushed stone). The thickness of the entire track is about 7-10 cm.
There is such a nuance - the path must be laid in one day. First the rough layer, then immediately the finishing layer (we lay it out carefully with a shovel) so that they are one whole. If you start pouring in the morning, then by the end of the day or even after 4 hours you can cut out the top of the path to look like a stone.
MY CHANNEL: @WOODIE-BY
If you do it thoroughly so that the path is really strong and does not crack, then it is worth doing so.
Clean the place. Remove the top layer (turf) with a shovel (depth of turf removal is about 14 cm). If you don’t want there to be puddles on the concrete surface, then you need to make a slight slope. For example, for every meter the slope is 2 mm.
Make formwork. It can be lubricated with detergent so that it can be easily removed after work.
Then geotextiles are laid. But I think I can do without it. Pour sand with crushed stone fraction from 5 to 20 mm.
Sprinkle well with water and compact. Then spread a plastic garden net. You can buy the cheapest one.
Then lay reinforcement with a diameter of 6 mm. You can do it without reinforcement, but add fiberglass to the solution. I also heard from professionals that it’s good to add a plasticizer to reduce the amount of water in the solution and then the concrete becomes especially strong. But I think I can do without it so as not to spend extra money.
Proportions
Fill the rough layer with cement with the addition of crushed stone. For a bucket of cement (grade 400, 500) there are 2 buckets of sand and 3 buckets of crushed stone. After pouring the rough layer comes the finishing layer (mortar without crushed stone). The thickness of the entire track is about 7-10 cm.
There is such a nuance - the path must be laid in one day. First the rough layer, then immediately the finishing layer (we lay it out carefully with a shovel) so that they are one whole. If you start pouring in the morning, then by the end of the day or even after 4 hours you can cut out the top of the path to look like a stone.
MY CHANNEL: @WOODIE-BY
Переглядів: 94
Відео
CHICKEN FARM. MAKING A "BROODER" is easy and simple. (old video).
Переглядів 184Місяць тому
CHICKEN FARM. MAKING A "BROODER" is easy and simple. (old video). "Welcome to our channel! In this video we will show you how to make a brooder for chickens from boards and other materials. We will demonstrate the process of creating a cozy place for young chicks, where constant lighting will be provided, an optimal temperature will be maintained, as well as access to food and water. You will l...
IMPRESSIVE JOB - Restoration of a forged axe.
Переглядів 1,1 тис.Місяць тому
UNIQUE work of a MASTER to restore an ANCIENT axe! In this video you will see the fascinating process of making a unique ax. The craft master will show you every step of creating this weapon: 1. Select the appropriate material to make the axe. Typically steel or iron is used. 2. Form the material into an ax shape using a hammer and anvil. This requires precision and careful work. 3. Then start ...
UNINTERRUPTED signal reception! MANUFACTURING HOME ANTENNA@
Переглядів 4262 місяці тому
UNINTERRUPTED signal reception! MANUFACTURING HOME ANTENNA@ Manufacturing an antenna can be done using the following methodology: 1. Materials preparation: selecting a suitable material for making the antenna, such as metal wires, printed circuit boards, or other materials with good conducting properties. 2. Antenna parameters calculation: determining the frequency of operation, type of radiati...
DETAILED GRINDING / GREAT KNIFE made from an old saw!
Переглядів 3,2 тис.2 місяці тому
DETAILED GRINDING / GREAT KNIFE made from an old saw! AN OLD SAW is a great option for making your first knife. This is a high CARBON content STEEL that is very EASY to work with. In this video I will teach you how to make a BUSHCRAFT style knife USING MULTIPLE TOOLS AND GET A GOOD RESULT. I HOPE YOU ENJOYED THE VIDEO, QUESTIONS IN THE COMMENTS! THIS KNIFE MAKING METHOD IS IMPRESSIVE! KNIFE (SI...
THIS KNIFE MAKING METHOD IS IMPRESSIVE!!!
Переглядів 5 тис.3 місяці тому
THIS KNIFE MAKING METHOD IS IMPRESSIVE! In this video you will see the process of making a knife - an unusual polishing technique. The master will show you all the stages of work, from choosing the material to final sharpening and polishing. You will learn how to create a unique and functional knife that will serve you for many years. MY CHENAL^ @WOODIE-BY
THESE HANDS MADE AN INCREDIBLE KNIFE!
Переглядів 3,6 тис.3 місяці тому
THESE HANDS MADE AN INCREDIBLE KNIFE! In this video you will see the process of making a knife - an unusual polishing technique. The master will show you all the stages of work, from choosing the material to final sharpening and polishing. You will learn how to create a unique and functional knife that will serve you for many years. MY CHENAL^ @WOODIE-BY
UNIQUE work of a MASTER to restore an ANCIENT axe!
Переглядів 9 тис.3 місяці тому
UNIQUE work of a MASTER to restore an ANCIENT axe! In this video you will see the fascinating process of making a unique ax. The craft master will show you every step of creating this weapon: 1. Select the appropriate material to make the axe. Typically steel or iron is used. 2. Form the material into an ax shape using a hammer and anvil. This requires precision and careful work. 3. Then start ...
THIS KNIFE MAKING METHOD IS IMPRESSIVE!
Переглядів 863 тис.3 місяці тому
AN OLD SAW is a great option for making your first knife. This is a high CARBON content STEEL that is very EASY to work with. In this video I will teach you how to make a BUSHCRAFT style knife USING MULTIPLE TOOLS AND GET A GOOD RESULT. I HOPE YOU ENJOYED THE VIDEO, QUESTIONS IN THE COMMENTS! THIS KNIFE MAKING METHOD IS IMPRESSIVE! KNIFE (SIMPLE). SUBSCRIBE HERE: @WOODIE-BY
IMPRESSIVE BATTERY RESTORATION METHOD!
Переглядів 1,1 тис.3 місяці тому
The method of restoring a battery using soda can be dangerous and not effective enough. CHANCE OF RESTORATION IS 50%. However, if you decide to try this method, you should follow these steps: 1. Prepare the necessary materials: soda (sodium bicarbonate), distilled water, ELECTROLYTE. 2. FOLLOW THE VIDEO INSTRUCTIONS. 3. Check the functionality of the battery by connecting it to the device. GOOD...
DIY FLASHLIGHT FROM A BULB!
Переглядів 8684 місяці тому
To make a flashlight from a light bulb and a battery, you will need the following materials: 1. An ordinary light bulb. 2. Battery (usually a “AA” or “AAA” battery is used). 3. Wires. 4. Suitable battery holder. Steps to create a flashlight: 1. Prepare the wires: cut two pieces of wire about 15-20 cm long. 2. Prepare the light bulb: expose the ends of the wires and connect them to the contacts ...
IT'S TERRIBLE WHEN YOUR HOUSE IS DESTROYED / WE ARE BUILDING A HOUSE FOR THE BIRDS! - DIY.
Переглядів 4034 місяці тому
Bird houses can be useful, especially if you want to attract birds to your garden or property. Here are some reasons why bird houses can be beneficial: 1. Shelter and protection from weather: Houses provide birds with protection from the elements, cold, wind and rain. They can use the lodge for overnight stays or as temporary shelter. 2. Nesting place: Many bird species prefer to nest in closed...
AMAZING - (CUT, Chop, CUT)! MAKING THE SHARPEST KNIFE FROM A BAND SAW!
Переглядів 262 тис.4 місяці тому
AMAZING - (CUT, Chop, CUT)! MAKING THE SHARPEST KNIFE FROM A BAND SAW! An OLD SAW SAW is a great option for making your first knife. It is a high CARBON STEEL that is very EASY to work with. In this video, I'll show you how to make a style knife (SANTOKU) - a versatile Japanese kitchen knife. "Santoku" literally translates as "three good things" or "three uses", which indicates the suitability ...
How easy is it to fill with gas?
Переглядів 6434 місяці тому
How to easily refill a gas burner? 1. Check that the gas burner is turned off and cool. 2. Remove the lid or access the gas tank. 3. Connect the hose from the gas cylinder to the corresponding inlet on the burner. 4. Open the tap on the gas cylinder to supply gas to the burner. 5. Check connections for leaks using a soap solution or a special gas detector. 6. Close the lid or replace the burner...
DON'T THINK OF THROWING OUT THE FOAM ⚠️ INCREDIBLE GLUE RECIPE!
Переглядів 8754 місяці тому
Tricks of masters and useful devices!! And you didn’t even know!! Useful tips! Tricks of the OLD MASTERS! LIFE HACK ideas at home for the workshop and home! SECRETS of the masters! DON'T THINK OF THROWING OUT THE FOAM ⚠️! INCREDIBLE GLUE RECIPE. Making the most powerful glue. We create homemade products with our own hands at home, devices, and amazing devices. After all, every tool or homemade ...
BURNING TABLE - incredible work made from old boards.
Переглядів 5434 місяці тому
BURNING TABLE - incredible work made from old boards.
“EASY” - we make an amazing sharpener for knives and saws!
Переглядів 2,8 тис.5 місяців тому
“EASY” - we make an amazing sharpener for knives and saws!
DIY | With only one ax we make an ax handle (ax handle) in 20 minutes quickly, understandably.
Переглядів 3315 місяців тому
DIY | With only one ax we make an ax handle (ax handle) in 20 minutes quickly, understandably.
SHARP KNIFE! - MAKING AN AMAZING KNIFE SHARPENER.
Переглядів 1,5 тис.5 місяців тому
SHARP KNIFE! - MAKING AN AMAZING KNIFE SHARPENER.
THIS KNIFE MAKING METHOD IS IMPRESSIVE!
Переглядів 719 тис.6 місяців тому
THIS KNIFE MAKING METHOD IS IMPRESSIVE!
⚠️WITHOUT GRINDSTONE! We sharpen knives like razors. You can even shave with this sharp blade!
Переглядів 18 тис.7 місяців тому
⚠️WITHOUT GRINDSTONE! We sharpen knives like razors. You can even shave with this sharp blade!
SHOCKING FIND! THE KNIFE IS NOW INCREDIBLY SHARP!
Переглядів 35 тис.7 місяців тому
SHOCKING FIND! THE KNIFE IS NOW INCREDIBLY SHARP!
WOODIE | Few people know about this roulette function! Hidden features of roulette.
Переглядів 2097 місяців тому
WOODIE | Few people know about this roulette function! Hidden features of roulette.
⚠️ WOODIE | Melee Weapon - "TOAD KILLER" (DIY)™.
Переглядів 2,1 тис.7 місяців тому
⚠️ WOODIE | Melee Weapon - "TOAD KILLER" (DIY)™.
WOODIE | THE SECRET OF THE PERFECT KNIFE (DIY).
Переглядів 28 тис.7 місяців тому
WOODIE | THE SECRET OF THE PERFECT KNIFE (DIY).
техника безопасности на высшем уровне))
Пора открывать платную школу мастерства, пилла особенно впечатляет . Котенок слепой потому что пробегал мимо.
The red circle round that ciggie tho aye
Гоано, а не способ. 👎
Зубья для кишок наружу?
если для себя то пойдет, на продажу, не выгодно будет
Капец! Хоть бы не позорился.
Одного меня впечатляет, что он не покалечился?
нормальную ножовку испортил . лучше купи себе попугая на плечо и иди в пираты. 😁👍
Nice looking knife but I prefer a forged knife.
Почему фултанг не зделал? Ведь хватало полосы….
Заточка такая себе
Кого впечатляет этот метод изготовления?
Аккуратная работа. 👏
ВСЁ ЗБСЬ, видно старую школу)))
Это наверное сталь быстрорез ее калить не надо😊
Смех, А4 в двое сложили и режут ппц
А из кровельного железа проще и быстрее, а качество и прочность будут схожи))
Думаю что лезвие из ножовки очень тонкое и держать заточку тоже не долго будет,сталь не очень хорошего качества.Думаю из пилы с пилорамы намного лучше бы получился нож.
дядь я такой же хочу , свяжись со мной я готов приобрести
Я тоже хочу такой нож
Супер! Можно сказать на коленке.
Бля, Горе мастер
Extraordinario
Шпатель
great looking knife. But doesnt anybody forge anymore
R u kidding??! I don't see any knife...
Мама зона
Котак сектыме якши !
Дело в том ,что ножовка по дереву имеет зонную.закалку ,и более менее приемлемая твердость со стороны зубьев .
Хороший нож. Здравствуй ржавчина)))
Ню из ножовки мачету для полисадника воял. В полисадничке малость порубить сойдет. Точится не ахти.
Хороший рабочий нож. Со своими задачами справится.
Бумагу режет очень слабо
Мужик молодец безусловно,но назвать это ножом потому что внешне похож язык не повернетсяу,если только кухонным,а так от скуки классно
Не делайте так!!!!!!!!
Как сверлили отверстия? Может я просмотрел
artista!
Без полезная вещь😅
Estragou o serrote pra fazer uma merda dessa
Просто бергите себя здоровья дороже чем эти ножы
Бред это не нож, это металлолом.
Займитесь чем то другим...
Дизлайк за игнорирование ТБ.
Woodie don't give a eff ! Uses his cigarette to filter the dust instead of a mask !! Hell YEAH! Safety is a myth. We all gonna die of something. I'm right there with you Woodie. I smoke and don't wear masks much... and I make knives too ...👍nice knife.
well you have as much sense then as he does,,,,daaaahhh none...
@@douglasbear68 yup ! That's what they say... though I scored highest in my schools history for mechanical aptitude. Still standing record. We all gonna die . I don't cling to this physical life because I know I'm immortal.
Что то похоже на Толяна ? Что с Украины свалил , у него там была шушера блоги вёл по почерку работ вижу похож 😂 , интернет помнит всё !
Удивительно! -из пилы сделал пилу!!
para comer el oxido bañalo en cocacola o algo asi, no le pases lija por que si ya de por si es delgada la hoja mejor no andar comiendole mas
amigo, eso no sirve para gran cosa... esteticamente puedes hacer algo bonito, o te puede sacar del paso para pelar una manzana o cortar alimentos, pero ese cuchillo para el campo es poco util... si eso se esta doblando solo con pasarle la radial....eso es finisimo
А слабо из нескольких таких дерьмовых ножей сделать более менее нормальную пилку ножовку ???????? Я думаю тут ужо ума не хватит.....