Відео

Thanx for this video , good instruction.

can the lifting be adjusted on this manifold?

NEVER install the spools without oil. They are very finely machined parts and seal the oil between passages without o-rings or other seals. If you scratch the surfaces, you can change the valve body to junk. I would never have this guy work on my equipment if he assembles dry.

Ok

Hi I love your videos very informative but I have a problem. I have a gray market half ton Kubota excavator which When I went to clean the control block I took out the spool valves and didn't mark their locations. You cannot get any information or manuals for this unit so I was wondering how I can tell where these valves belong. Thanks in advance. It's a Kubota k005

Hi I love your videos very informative but I have a problem. I have a gray market half ton Kubota excavator which When I went to clean the control block I took out the spool valves and didn't mark their locations. You cannot get any information or manuals for this unit so I was wondering how I can tell where these valves belong. Thanks in advance. It's a Kubota k005

you deserve so many more subs,# hiddenjem

I'm sure this guy is a really nice person, but he shouldn't be sharing his very incorrect information with the world. The clearance between the spool and the spool bore of a hydraulic control valve is concerably less than 0.001" Even the most basic directional control valve has between 0.0001" and 0.0003". (That's from 3 to 8 μm for the metric minded). The tool this guy is using is has a resolution of 0.0005" (13μm). But, its accuracy is 0.001" (25.4μm). The tool is 3x less accurate to evaluate this assembly. Also, a partical of .00016" (4μm) that gets into the closed assembly will cause at least minor damage to it. His attention to cleanliness is horrible and it's really difficult to remove small particles once the get into the valve body. They get trapped in the corners and are incredibly difficult to flush out. Overall, I give him an F- for his skills in hydraulics. However

How you end play of engine

Hi

Hindi mein bataen

Are we just going to ignore the fact that according to his precision measurements the spools are too big to fit in the bores lol.

My spools get stuck I smoothened them they worked for some days then it got stuck again

my whatsapp line

i need help from you

I wonder if the guys in the back are still balancing that tire

Excellent work.

Not accurately measured at all,, wrong measuring tools and procedure.

Generally, people get into valve bodies because of lost control: something either isn't happening, or won't stop. Very important to check for trash first, then measure. Spools usually tell the story.

ua-cam.com/channels/8PyuNI0Gcydfj4g8xkfp5Q.html

So are the spools only sealed by a film of oil or is there an o-ring inside the valve body to prevent leaks to the outside?

how fucking idea to write english with speaking we cant see what he want to physical said or mentioned please change this dnt mentioned fucking english

I had my hydraulic valve re sealed on my john deere 6675 skid loader. I added hydraulic fluid and did not bleed after starting I tried forcing the up on the bucket to work because it was hard after forcing the pedal it made a loud bang noise and blew the fill cap off on the hydraulic tank. What did I break or destroy?

Thanks for the explanation! Nice video, what is this engine used on?

Hydraulic valve @t

Como montar a mola da aste

So I’ve got a leak at the spring cover cap it’s not a bad leak but I want to fix it anyone know if it’s a seal or something

Thanks for the information. God bless you! Have you placed your faith in Jesus Christ, the Son of God, so His righteousness will be imputed to you then you will go to heaven instead of spending eternity in hell for your sin when you die?

Although I was looking on how to dismantle the valve, your video helped my figure it out from assembly. Thanks!

Hidrolik combin yg tidak ada, kalau bisa , jga d tanbilkan , cara mengatasi hidrolik x yg lemah.

It can not checked by vernier , use micrometer for accurate result

Lakhan Jadhav

How would you get an accurate reading when the crank can move in the direction you're measuring too?

Shity video zero explanation and bud learn to use the right side of the bar

This is how to damage expensive commercial rims, just use the machines, no back pain no costly damages

How can I get the tools for the valves adjust

Wrong way to use bars

nice voice lol!!!!