Відео

❤

Backstabbed outlets, everytime lol

WTF is a "solar deck"? Can you use common terminology for those of us not in the industry? Are you removing the panel to check the optimizer beneath it or what? And what specifically are you doing when you are checking it?

So u changed 5 optimizers that all coincidentally failed on the same string? What are the chances it wasn’t just the ground?

I have a Drok model EM3005 which is an AC meter that should register 40 to 280 V and current from 0 to 5 Amps. There is no CT just 4 connections. Ever seen this type? Thanks.

I am installing a Drok "AD16-22AM" AC Amp meter. For a 120 volt circuit, what size wire would you use to connect the meter to the line & Neutral of the source? I am monitoring a outlet of a Voltec T-Box Nema 5-20R

В мене температура до 77© чи це нормально?

The rear block should be flipped over so you can place a soft thermal pad inside, this should cover the entire backside contact area of the back waterblock. Then you heat it all up with a blow dryer (NOT A HEAT GUN) and get the block hot, and GPU PCB nice and hot! Then you place the rear block and press it down and squish that full coverage thermal pad, the full cover pad would conform to the entire back of the GPU. Your temps would be literally ridiculous..You are essentially transferring all of that metal/water cooling surface area to the entire back side of the GPU. And not just those tiny pieces of gimpy thermal pads you are using. Optimus PC sells the 3090 FTW3 “Full coverage backside” Fujipoly branded 3MM thick ultra soft thermal pad for $38 bucks. It is a perfect fit for your GPU with holes pre-cut.

Better looking for another JOB, isolation faults are always related to bad installers keeping wires and mc4's on the roof and not properly mounted to panels and aluminum bars.

How do I determine where the ground fault is if my safety voltage is the correct measurement

Thanks for the helpful video sir.

my solaredge system is just recently giving this error....system working for 2 years and no error... I have found the bad string that produces the error....the bad string has 8 panels....and still producing 8v across the pos and neg ... it appears to give the fault in the mornings after rain during the night ... the moment the sun shines I see the isolation value rise above 600kohm and the error disappears and the system starts producing again... any idea what this could be in your experience... its moisture related??? ...

Just figured I’d mention mine are 1mm, 2mm, and 2.5mm. Used the sizes you showed and they do not touch anything lol I ordered some more

Quick question I’m using the same GPU in my main PC but the fan is starting to rattle, I dusted it but it’s still giving me a loud noise while in use. Could I swap out the GPU fan with any other regular fan as a replacement?

Want to see a megger test

Thanks for detailed the procedure on this GPU, have the same model and your vídeo helped a lot! 👍

On the bottom what size thermal pads did you settle on on the 3090 ftw3 with the bykski block? 1mm/1,5mm or both?

It's a lil bit annoying that you have to remove all the screws just coz 1 of the fan screw it's inaccessible, in case you need to replace the fan like me, i don't see the logic in this construction method

Thanks, i have this laptop tho mine came with 16gb ram standard, is there much performance change upping it to 32gb ?

How much money do you make on mining?

Great video. Makes me believe I could do the same one day. Very exciting! Just not sure if it's worth it. I downvolted the card and gpu is about 67 degrees on high load. The card has 10 year warranty. If I break it apart, no more warranty probably?

Can I put 2 TB in it?

Just bought one used and going to do this incase its a mined card

Can I use this size of thermal pad on Pny Gtx 1660 super dual fan

Thank you! Worked on my 3090 Ti

i wanted to kill myself watching this video ...

I've found using cut "round tooth picks" to 3/4 length of their original length, then place them (cut side down, pointy side up) "diagonally" in the cooler screw holes helps to align the PCB holes as you slowly lower cooler block onto the PCB. While leaving the 2 tooth picks in their holes, insert 2 screws into the other empty holes, lightly tighten. Then remove the tooth picks, insert the other 2 screws and lightly tighten. Finally, diagonally tighten all screws to a firm tightening. Done this procedure on ALL my GPUs when replacing thermal pads. No guess work on IF cooler & PCB were mounted right and keeps them from sliding before putting screws back in.

thanks very much. what thermal putty did you use? thanks for all tips.

I used byk GPU block, your comment about the thermal pad is spot on. their 1.8 thickness doesn't work.

Thanks for your help. I just did my 3090 last night and wasted my 1mm thermal pads. The 2mm pads they included are the right size. If I use 1mm it’s way too thin. I also stacked the pads for the chokes but might make like a copper spacer for it.

What is code 18xB8

why after every word is it an power point transition

Very well explained help me out so much thanks man

Can I use only 1mm for this model?

So, spend 400 get 30... no thank you. Doesn't sound like that good of a deal to me lol... they have PLENTY of free games from what I hear lol

🚫🐿🚫🐿

giga hash *

Can I put 1tr hdd + ssd in or just ssd

Thanks for the info

Nice little video. I just picked up three 3070 FE's. Can't wait to get them mining. Cheers!

Can i get some help, When i try to download unmineable it says interrupted network, but when ever i download anything else it works?, what should i do

MSI afterburner work with other pc like hp?

Those damaged wires aren’t they on the AC side? Where was the actual ground fault?

Sir i'm from India and i want to buy specially nividia founder edition cards only from USA and i want these cards 3060Ti, 3070Ti, 3080, 3080Ti lhr and non-lhr cards both . May i get any of your contact number or mail id to talk to you

Sir i'm from India and i want to buy specially nividia founder edition cards only from USA and i want brand new cards at msrp likes 3060Ti, 3070Ti, 3080, 3080Ti lhr and non-lhr cards both

nice bro

Lines up with what I get. I mine Ethash on it and get 38 Mh/s.

The temps are awesome dude! And you used only one card... Maybe not all miners are villains 😂

sad

Bro your cpu block is upside down. I did the same thing lol and ran the cable to the left after I flipped it