Відео

Dam all that an could cut it

I've been in that situation and here's how I avoid it now. Every year I crack open each bleeder then every second year I replace all of them with new ones. They never get the chance to freeze in place that way. The money saved by not adding to the swear jar pays for the bleeders.

Bin doing this type work for 40 plus years ! Your best tool and freind is wd 40 and PB blaster one major hint and advise is next time PRE SOAK with blaster 24 to 48 hrs before you want to do it !!! This is what I do and works every time for me first hit gently straight down with small hammer to crack rust on threads then apply pb or wd at least 3 times over a 24 hr period 48 is best and walla

Why is it hard? Because apparently American greed has turned our once proud trucks to sh!t

Very neat. Could use a little TLC to adjust the tolerances. It would improve the flow rate and that noise.

Why don't you put 4x4 on video👎👎👎👎🤦🤦🤦😡😡

Thank you, I'll copy this at the weekend

Can it pump high viscosity fluid?

Hello, I have considered doing the same thing but I am concerned with propane and electricity. What precautions should be taken? I am strong in C and C++ dev and pretty strong in electronics. I know very little about propane. Are you concerned at all with sparks? Arduino is low volt dc but even +5v can spark. The servo at the top of the propane tank is probably my biggest concern. EDIT: I just saw the fire extinguisher which is good for a fire but my concern with propane is spark+gas==boom

Net time quench it with some cold water after its hot. It will shock it, and makes removal much easier.

Lucky that the Easy-Out tool didn't break on you ... it happens and then you are in real trouble! No need spray clean the inside, you reamed out the hole with a paper towel and added anti-seize to the new screw and that is good enough. It won't sieze up again.

They look great! Awesome build!

awesome job, thanks to share

Painting that beautiful concrete is downright savage. Nice project though!

Nice work I found the best way to fill the pinholes is to sand with 50 grit Then wet sand with 100 grit and a slurry made of acrylic and cement. The cement binds with the material you are removing from the concrete and forces it in to all of the holes. Once that dries I sand with 200 and so on.

think maybe 20 buck links is why the rubber split....idk

Yes.... videos are back!! 😁 Keep it up!

PB blaster, presoak that stuff and let sit overnight, or even a few days if your a procrastinating soul.. That stuff is great, but not good on condoms so dont use it lube that shaft lol.

This is super clever, how durable has it been? Any suggested components to scale it up to 2"-3" hose?

My detroit axle swaybar links broke within a month of install. Just saying🥴

Glad to see they keep you honest with a swear jar.

Looks like a nice rust free underside. You should see my winter 03 ram. Lol rusty as hell. It's in my videos

Subd too

Fix it up ...it has low miles. I have a 03 5.7 with 256k and a 05 with 160k. All original except rear end rebuilt in the 03

Nice video bud

put some goddamn lights on.

Dude, are you in Raleigh? I just bought a house in Durham!

Comparisons with the carbo Tenore? I just got in on the drop for the pros whilst owning the Tenore for a while now

Sub'd! Can't wait to see more! Good job brother!

Thumbs down for vertical video Thumbs up for VERY clever cheap+durable design XD

Hi, I want use this device for two 18B20. www.tweaking4all.com/hardware/arduino/arduino-ds18b20-temperature-sensor/attachment/ds18b20-parasite-power/ Is it correct? Thank you.

Hi, could you help me for 2 peace DS 18B20 and arduino corrections? I try 2 way first (pin 1 and 3 to GND and pin 2 pull up 4.7K to 5 V) . and Second ( pin 1 to 5V, Pin 2 to 4.7K via 5V and pin 3 to GND )versions but I read upper and lower temprature -196.6 and servo angle 1520 and servo contuniously turn clockwise. Thank you.

55555

Check InpliX handbook if you want to make it cheaper and better.

IF you want to make it by yourself just go to InpliX page.

This vertical filming is extreme

so nice

need to get yourself some electric heating elements... mash in and walk away

simplest & the best

@pcproff it seems like there is an issue with sending data too fast, but I haven't had time to update the library. If you are more comfortable with photon, then maybe you can get it to work.

You heard any feedback from Adafruit? I'm looking to use it on my photon.

Where can you get a servo motor for the propane regulator? I haven't been able to find anything, is there a type of supply shop or store that would have them? I'm looking to use this idea to make a propane coffee roaster.

picture size is very small ,,camera shaking and camera is out of frame many time plz remake this with professional videographer

nearlynormal007 do you know what the flowrate and weight of the this pump are?

how did you select the correct Kp Kd Ki for the pid. congratulations nice project

You're pumping water downhill, anyone who's stolen gas needs you dont need power to do that. Not even at an impressive rate.

been looking for something cheap like this for ages, wonder if you could make me one with a motor that would pump mortar between the joints of brickwork a firm called refina peristaltic mortar pump have made one costs a fortune though check them out let me know if you could manufacture me one cheap.

Yay! A horizontal video! Good on you. I'll watch this one! Thanks for sharing the info

Come on man. It's 2014, people should know that when you shoot a video with a phone you hold it SIDEWAYS.

Vertical Video Syndrome - A PSA Thanks for the informative video though