Відео

Sorry sir, but your job is not yet completed. 😆

軽自動車のナンバープレートを見るまでアメリカと思ってた🤣 日本でもこんなトラックあるのはすごいですね！

Did he leave the other bolts in on opposite side but just loosen them? If not whats keeping the bed from sliding off at that angle ?

That engine bay looks showroom new

This Must be a instructional video for deaf people😮

Why aren't you talking or is this video for deaf people?

What size did you use

Thank you for making this video. Makes the job so much easier.

And it never ran again😅

Great video

Awesome job. Thank you for sharing this video.

Why is it that you never say a word through the hole video. Like maybe what size socket your using?

Best video on UA-cam so far to search for! Great angle ! And straight to the point!

Just so you know don't crack that little hose that plugs into the bottom of the sensor no one on the entire internet knows where to find a new one.👍🤡👍

Thank you!!

Any idea what the orange gasket is called around the manifold? Been trying to replace it & having no luck finding any

Was it the same after the map sensor change??

Great video. Thanks for not wasting our time with a 15 minute introduction. Thanks for stopping so we could see it was a 13 mm socket. Fantastic and quick and to point.

So you’re not gonna explain a damn thing huh. Thanks for nothing.

My thermostat has a little hole for air bubbles I guess and I put that in the 10oclock position, is that gonna be fine ?

How about at least explaining the process or even showing what the hell you are doing.

I’m confused, are you showing just how to change out the map sensor or was it throwing a code?

Good job

Ur video sucks cause if it's not ur entire arm being in the way it's the bag.

Direct and to the point, thank you i will get on mine this weekend. Love that its straight to the nitty gritty, not 5 or 10 minutes of a person talking.

What is that 2 pronged wire you connected to the terminal?

What size did you use to get the bolts off?

Do you have any heater problem? Like the heat only blows warm?

Feel like I’m going to rip something out when I go to pull the hose off the heating core end

Say something

I changed the pump on mine a week ago an had to drop the tank. Turns out the thing was pretty loaded with scum in it. Cleaned the tank out but i think i messed up and didnt hookup the extra wire off the pump because the gauge reads zero gas.

Lol couldn't figure out how to properly get the pulley off

electric fan....4 bolts....5 minutes to remove it....Guess you prefer a challenge

What size socket did you need

The 97's don't have enough fuel lines to drop the the fuel tank without causing even more damage. Takes 10 minutes to remove 6 bolts from the bed, disconnect electrical wires from the tail lights, and have three people to remove the bed as you have so much easy access now. Shifting the bed is also optional.

I usually see people just replace it with a fuel pump.

Thanks for this video Kanekk! I hear mixed reviews about WD-40 and rubber. Here's a video of someone who tested rubber soaked in WD-40. He saw some swelling and softening of the rubber: ua-cam.com/video/HfcEPso4YoY/v-deo.html (skip to around 12:30). Also curious how filling up the zerks worked out for you. Did the new boots contain the lubricant well or did they leak? Thank you!

Do you need to jack up the truck at all to do any of this?

Anyone know if this is the same procedure for a pre 1996

That will be 500 thanks

Hey, 97 5.7. Gets about 55 Fuel pressure and then drops. That sounds like a pump problem?

To lower tank, must wrestle with fuel removal, where to store that gas? then unstrap the tank and lower same. Am doing it right now on sloped driveway ugg.

Dropping the tank is easier but those comments get buried because they want the bed to fall on you while working in there so you can get hurt = more money to them.

I felt the pain with that pulley, it can sometimes be a nightmare pressing them on with that tool.

Fast, practical and without detours. Excellent video! Thanks, it was a great help.

great video, great camera angle. straight to the point.

thanks for taking the time to do the video, I did the same on a dodge because I am in the rust belt. I just used an engine crane a bit more crude but it is an old truck so wasn't worried about marking up the bottom of the box edge on front. We left the rear bolts in loosely to keep alignment just lifted the front. Cheapest fuel pump I could find and it's lasted years lol

Cambie la bomba pero porque derrama aceite de la polea????

Thank you man. Alot of people skip right over the actual pump install.

Any particular reason why you went with the 180 thermostat instead of the 195 degree? How’s it running and did gas mileage or heat during the winter change?